How can i convert aerogel into powder for xps. i treid to grind it but i couldn't?

05 September 2023 1 2K Report

i need powder form of my aerogel for xps analysis, how can i do that.

Bikash Kumar Sahu

Apparently you couldn't make the airgel brittle at room temperature. Depending on the solvent (water, alcohol...) cool the gel to the crystallization temperature of the solvent, and then disperse the airgel.

Badges
Science topic

More Bikash Kumar Sahu's questions See All

Is this a facetotecta nauplius?

This larva was captured using a plankton net in the Persian Gulf during the summer. I believe it may be a Facetotecta nauplius.

08 August 2024 3,746 4 View

How select composition for ods-high entropy alloys?

31 July 2024 2,795 1 View

Following click reaction in cell lysates, protein is immobile and remains at the top of the gel in SDS-PAGE?

I am using CuBr/THPTA for a click reaction in total cell lysates. I am facing issues with my protein sample in non-reducing SDS-PAGE where it's not migrating properly and most of it remains at the...

29 July 2024 950 4 View

Which filtration method to go for run off water from dirty solar panels to be used again?

We are working on a robot that cleans solar panels using fresh water supply and a rotating brush. We are trying to conserve as much water at possible by recycling the dirty water that is collected...

28 July 2024 5,778 2 View

When making abraxane with Nab tech, why is 9:1 Chloroform&EtOH used as solvents?

Is it the best optimization ratio based on experiments?

22 July 2024 8,170 0 View

Can diamond be grown using molecular beam epitaxy?

22 July 2024 9,755 2 View

How can I use LabVIEW to control of an ethernet-based driver?

Hello everyone, I am new to LabVIEW, right now we need to control the movement of an ethernet-based stage drive. We got the sample code from a collaborator but their instrument is USB-based, so we...

11 July 2024 5,385 2 View

Systematic review meta-analysis paper?

Hi everybody, We are trying to write a systematic review meta-analysis paper. But I could find 19 references. I think 19 references are not enough to do a meta-analysis section and it is better to...

10 July 2024 5,490 5 View

Do the SHSY5Y cells tend to form multiple layers over each other when highly confluent?

I have attached pics of the SH-SY5Y cells within a seeded plate after reaching >80-90% confluence. Are these dark clumps of multiple growing cell layers? Or dead cells? Any clue? many thanks.

01 July 2024 8,361 3 View

Adding isopropanol directly to eluted RNA samples?

I have my RNA samples eluted in nuclease-free water. But now I want to store it for a longer period. Can I add isopropanol directly to my samples to store it without doing a second round of TriZol...

23 June 2024 2,576 4 View

How to solve the problem of unconscious teeth grinding during sleep at night?

One of my friends, every night after falling asleep, his mouth would make a creaking sound after chewing something. This teeth grinding condition would continue until he woke up, and he didn't...

08 August 2024 1,366 5 View

Mechanochemistry: ball to powder mass or ball to powder volume?

I run mechanochemical reactions that involves the use of a large amount of catalyst (1:1 molar ratio to the reactant). When I try to understand the effect of amount of catalyst on the reaction, I...

23 July 2024 9,938 1 View

I want to plot calibration curve of pure mirtazapine powder using HPLC. Can someone please suggest a method without HPLC buffer as a mobile phase?

I am searching for HPLC method to estimate Mirtazapine but i want to avoid HPLC-buffers as a mobile phase component. So, I am looking for alternative HPLC-solvent (acetonitrile, methanol etc.)...

14 July 2024 1,493 3 View

What binders suggestion that I can use for zinc alloy?

I am working on powder metallurgy, and during the compaction process, the powder does not pelletize and remains in its powder form. To address this issue, I am considering using binders to improve...

13 July 2024 9,003 2 View

How i figuer out the weight of curcumin powder?

I am trying to load curcumin emulsion in 4% chitosan gel but i don not know how many mg powder is needed ?

10 July 2024 2,462 1 View

Can anyone suggest what amount of powder I have to disperse in the solvent for taking the FTIR spectra?

I have to compare the FTIR of the two samples, one is in powder form and other one is the powder dispersed in IPA or water. Both are same material, so how the bond will change

09 July 2024 8,011 2 View

Is VSM measurment of NdFeB alloy powder sample require any spesific sample preparation ?

Is any specific sample preparation required to perform VSM measurement of NdFeB alloy powder to get a square-shaped M-H loop? Or is it mandatory to make magnetically aligned and sintered pellets...

09 July 2024 1,969 0 View

I have need a LPBF/SLM model on comsol multiphysics ?

In this model clearly understanding how to active one layer to another layer and how to add powder material properties step by step.

08 July 2024 6,147 0 View

Good evening, I would like to evaluate the heavy metal content in bird feathers. Can I keep my samples in powder form ?

Good evening, I would like to evaluate the heavy metal content in bird feathers. Can I keep my samples in powder form ? and can I use other tubes than Teflon for digestion?

04 July 2024 158 4 View

How do I make a solution from fibroblast growth factor since it is available as a powder?

I am using fibroblast growth factor, purchased in powder form. What suitable substance should be added to get it in a liquid form? Thanks

03 July 2024 9,866 2 View