How can I calculate strenght to weight ratio from four point bending test in Abaqus?

More Sarath Arangat Jayarajan's questions See All

To generate the temperature map of a city, what resolution shall be efficient way of representation (eg:500sq.m or 1sq.km grids) ?

We have a telematics data - temperature values are collected per second. To generate a hourly map of temperature of a city, suggest the appropriate resolution. This map is not for any specific use...

20 November 2023 9,954 1 View

How to control parameters in Energyplus during Runtime Actuation?

Hi everyone. I’m trying to implement some papers that control a few parameters during runtime. I’m using Gym-Eplus to vary the values but I’m not sure if the following can actually be...

25 July 2023 8,075 5 View

How to parametrise the soil carbon sequestration?

What are the available standard equations for estimating soil carbon sequestration?

24 January 2023 1,231 2 View

How to define HFO2, Ti and Au in SILVACO atlas TCAD?

SOI MOSFET

11 July 2022 2,292 2 View

How can we set the temperature range for shelf life determination. As some books/journal starts from refrigerated condition and they elevate?

How can we set the temperature range for shelf-life determination? As some books/journal starts from refriigerated condition and they elevate to oven temperature and from that, they calculate the...

05 September 2021 1,195 2 View

Can we add pre emergence herbicide by mixing the chemical with sand and spreading in the rice field?

Herbicides like petrichlor mixed with 20 kg/acre sand and applied to the rice field. Is it a good practice?? If not suggest way of application rather than spraying.

10 August 2020 6,928 4 View

The use of PSG/MSLT to support a diagnosis of narcolepsy?

The use of MSLT to support a diagnosis of narcolepsy is suspect if Total Sleep Time on prior night sleep study is less than 6 hours My query is what are the other ways to confirm the diagnosis...

22 July 2020 6,580 3 View

What are the possible reasons for a primer dimer to occur in a PCR, LAMP reaction?

I am currently working in an isothermal amplification technique called PSR ( Polymerase spiral Reaction). I have followed the reaction mixture from previous articles but i am getting primer dimers...

15 February 2020 2,961 3 View

How does CRISPR-Cas system in bacteria recognize bacteriophage or viral DNA as lethal target?

i would like to know, how viral DNA's are unique when compared to that of the bacterial DNA. Why doesn't the CRISPR-Cas system activate for a bacterial DNA when it gets transferred to the...

19 June 2019 7,944 3 View

How to model Schottky diode SMS-7630 in ADS for rectifier applications at 5.8 GHz???

Hi all, I am trying to model the Schottky diode SMS 7630-079 LF for rectifier application in ADS for a frequency of 5.8 GHz. The data sheet provides absolutely no information apart from the basic...

28 April 2019 4,343 11 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

London dispersion in CCl4 vs the dipole-dipoles force strength in CHCl3?

How do you tie-break and rank these two in their strength?

03 August 2024 4,471 1 View

What are the limitations and challenges of using machine learning for predicting concrete compressive strength in practical applications?

Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...

03 August 2024 2,546 2 View

Simulation of metal drawing by Abaqus with UMAT?

Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...

30 July 2024 7,062 1 View

Why running a restart analysis in Abaqus in Ubuntu OS gives an error as attached when running the same job in Windows doesn't give any error and runs?

I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...

29 July 2024 9,572 3 View

How Can I Apply Hashin Damage Properties to Solid Elements in Abaqus Without Using VUMAT?

Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...

28 July 2024 8,169 0 View

Abaqus cylinder buckling riks analysis?

hi, I am doing a risk analysis of a cylindrical fuselage with windows. I have applied contact interactions between the different parts, and I have applied a unit value load to a reference point,...

20 July 2024 647 2 View

Rohola Rahnavard

Dear Sarath,

I ma not sure if I understood your question well. In general, strength to weight ratio is the maximum capacity over the weight of the beam.

Sarath Arangat Jayarajan

@Rohola Rahnavard, Let me brief my question, I need to design a specimen in order to undergo 4 point bending test in abaqus. My objective is to find the maximum strength in a minimum weight of the material.