How can I build an electrical model of Graphene coated copper?

Manareldeen Adil Hassan Ahmed @Manareldeen_Ahmed2

01 January 1970 0 5K Report

I am trying to build an electrical model of SLG on copper, what formula is suitable for this case?

Badges
Science topic

More Manareldeen Adil Hassan Ahmed's questions See All

How does graphene affect the density of states of copper?

how can graphene affect the Cu DOS ? If I calculate the PDOS at the surface, what should I look at to see the effect of the graphene on the total DOS and current transport ?

01 January 1970 5,607 0 View

How to measure the electric resistance of CVD graphene on copper ?

I have synthesized graphene on Cu foil and want to measure the electric resistance? what is the method/device that help me to get an accurate measurement ?

01 January 1970 1,050 3 View

What is the best method for Graphene coated Copper?

I want to use Graphene as a coating layer on copper electrode, which method is better, CVD or Graphene ink coating ?

01 January 1970 6,353 4 View

What is the best references that I can use to learn DFT?

I am interested in the quantum transport and the electronic properties of Graphene and nano-scale materials. What is the best way to learn the basics of DFT?

01 January 1970 1,553 6 View

For Graphene simulation, how to build an Unit cell ?

For Graphene simulation, how to build an Unit cell that consists of graphene and vacuum atoms?

01 January 1970 8,924 0 View

How to determine the high symmetry points of arm chair graphene unit cell ?

There is a lot of examples for two atoms unit cell of graphene, however, I have a unit cell of graphene (armchair) contains 4 atoms (attached photo). how can I get the high symmetry points for...

01 January 1970 8,348 2 View

How to build an electrical model from different values of thin film resistance?

I have calculated the resistance of a thin film of two materials for different widths and lengths. I want to build an electrical model for both materials and compare between them.

01 January 1970 7,624 0 View

Which method is better for Graphene synthesis, CVD or PECVD?

what is the main difference between PECVD and conventional CVD, and which one is better for Graphene synthesis on copper metal? and how to check the quality of the deposited Graphene?

01 January 1970 3,938 7 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

Short Synthesis of Graphene Oxide from Natural Graphite Flakes?

I am in search of a modified Hummer's method, which can be used to synthesis graphene oxide within 6-8 hours. As I am a student it is not allowed for us to work after 5 in the laboratory. So I am...

01 August 2024 8,368 2 View

How can I separate graphene from amorphous carbon of similar particle sizes?

The starting material is a finely ground powder. Some particles contain more graphene than others.

30 July 2024 3,978 2 View

What is the reason I get 400nm nanoparticles using an extruder with 200 nm membrane for cell membrane coating?

I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...

30 July 2024 3,294 3 View

Addition of EDTA during the synthesis of copper nanoparticles to prevent it from being oxidized?

I've attempted to use this method to synthesize copper nanoparticles. Copper nanoparticles can be synthesised using a variety of precursor materials. CuSO4, distilled water, NaOH, and EDTA are...

28 July 2024 8,027 3 View

What is the main used curing agent for epoxy based coating?

I am trying to coating metal oxide into steel substrate, for better sticking planning to utilse epoxy based, Could you please suggest suitable curing agent for the coating purpose

25 July 2024 438 3 View

How do you get pure primary macrophage cell culture?

I have been harvesting monocyte-derived macrophages from buffalo and cattle fresh whole blood using the same protocol for years and getting good macrophage cultures. Below is the protocol that I...

23 July 2024 4,074 2 View

Issues in coating of cathode material on Al foil, why we are not getting proper coating and results when the cathode was coated on Al-foil..?

We are trying to coat some cathode materials on Al-foil ( ex - LiFePO4 , S@CNT, etc). When we coated the Al foil with the cathode (ex - S@CNT) material , the cycling result was annoying. But the...

09 July 2024 5,123 4 View