How can I add (measurement) noise to a harmonic analysis in ANSYS?

Christoffer Lærkesen @Christoffer-Laerkesen

13 November 2020 1 7K Report

Hello.

I am using ANSYS mechanical APDL.

I currently follow the procedure described in

https://sites.ualberta.ca/~wmoussa/AnsysTutorial/IT/Harmonic/Print.pdf

I wish to add (measurement) noise to all degrees of freedom when performing a harmonic analysis of a structure.

How can I do this? Is there a function which can do this, or is it necessary to apply loads to all degrees of freedom?

I will supply any necessary information you may need.

Thank you in advance!

Kind Regards

Christoffer

S M Anas

Dear Laerkesen,

I suggest you try the following link:

https://youtu.be/m3ZyabKZATc

Regards,

Badges
Science topic

More Christoffer Lærkesen's questions See All

How does one extract FRF- and phase-data from ANSYS (APDL)?

Hello. Using the instruction in: https://sites.ualberta.ca/~wmoussa/AnsysTutorial/IT/Harmonic/Harmonic.html I am able to create frequency response and corresponding phase plots. I...

10 November 2020 2,471 1 View

How to create correct natural frequencies (in Matlab) from mass and stiffness matrices extracted from an ANSYS model?

Hello. For other purposes, which cannot be done in ANSYS, I extract the mass and stiffness matrices. As a check I use the extracted mass and stiffness matrices to compute the natural frequencies....

22 October 2020 4,947 3 View

How do I recreate natural frequencies from extracted mass and stiffness matrices (ANSYS APDL)?

Hey. I am currently extracting my matrices as: *SMAT, MatM, D, import, full, beam_test.full, MASS *print, MatM, MMAT_CBEAM_1.txt Then I load the matrices into Matlab. Then I formulate...

18 October 2020 3,070 3 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

03 March 2021 3,568 1 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

Do we need to write protocol for a second study of a systematic review that has been registered and published?

I have conducted and published a systematic review and meta-analysis research with the topic related to public health and health pomotion (protocol was registed in PROSPERO). Now we want to...

03 March 2021 8,920 3 View

How to increase a model accuracy ?

dear community, my model is based feature extraction from non stationary signals using discrete Wavelet Transform and then using statistical features then machine learning classifiers in order to...

03 March 2021 6,994 5 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Do I need to do linear regression before running mediation analysis using PROCESS MACRO by Hayes ?

I just wanted to check if I need to run a linear regression separately if I am using PROCESS MACRO to run mediation analysis. Thank you.

02 March 2021 4,359 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View