How apply boundary conditions in PLAXIS 3D ?

More Soumaya Hadri's questions See All

FLAC2D software could model the geotextile encasement using structural elements if an axisymmetric model was selected ?

In 2D modeling geosynthetic encased stone columns, FLAC2D software could model the geotextile encasement using structural elements if an axisymmetric model was selected ? Thanks in advance.

10 November 2018 10,060 1 View

How to calculate the new parameters of geosynthetic encased stone columns for the two dimensional analysis ?

How to calculate the equivalent cohesion (c), friction angle (Φ), Young's modulus (E) and unit weight (ɣ) of geosynthetic encased stone columns.

08 September 2018 5,727 2 View

What is the most method to predict the settlement of foundation on heterogeneous soil reinforced with Stone Columns ?

What is the most method to predict the settlement of foundation on heterogeneous soil reinforced with Stone Columns.

07 August 2018 8,160 3 View

What is the best software to use for 3D modeling geosynthetic encased stone columns ?

I am looking for software that could be used in 3D modeling geosynthetic encased stone columns. Thank you.

06 July 2018 1,171 19 View

How can i define properties of materials in FLAC 3D 5.0 ?

How can i define properties of materials and how apply boundary conditions in finite difference model FLAC 3D 5.0

04 May 2018 7,103 2 View

Are there exist version FLAC 3D 5.0 for 32 bit ?

I'm searching for FLAC3D 5.0 32 bit.

03 April 2018 4,418 1 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Who will be moral responsible for the death of thousands of people in the event of an earthquake?

Who will bear moral responsibility for the deaths of thousands of people in the event of an earthquake? Weeks and months remain before the onset of strong earthquakes that bring death to...

08 August 2024 6,134 12 View

Regarding LBM in Boiling?

What should be the equation for halfway bounce back boundary condition for flow field with forcing term?

08 August 2024 7,938 1 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

Stability of the Solar System: Insights from Einstein’s Equations ?

The stability of the Solar System is a complex subject that blends the classical framework of Newtonian mechanics with the modern insights provided by General Relativity (GR). Understanding this...

07 August 2024 2,569 1 View

Sajjad Emad Rasheed

Boundary conditions are automatically applied at the model extents, however, they can be modified at the phase construction window under "fixities"

Sukanta Das

Automatically applied at the model

Juneid Bakr

It could be applied by default to the model or you could use the prescribed displacement option at the end of the model and apply zero displacement in the direction you try to fix it.