Are there exist version FLAC 3D 5.0 for 32 bit ?

Soumaya Hadri @Soumaya_Hadri

04 April 2018 1 4K Report

I'm searching for FLAC3D 5.0 32 bit.

Alireza Ahadi

Yes.

https://www.itascacg.com/software/flac3d/updates/flac3d-501-32-bit

Badges
Science topic

More Soumaya Hadri's questions See All

FLAC2D software could model the geotextile encasement using structural elements if an axisymmetric model was selected ?

In 2D modeling geosynthetic encased stone columns, FLAC2D software could model the geotextile encasement using structural elements if an axisymmetric model was selected ? Thanks in advance.

10 November 2018 10,060 1 View

How to calculate the new parameters of geosynthetic encased stone columns for the two dimensional analysis ?

How to calculate the equivalent cohesion (c), friction angle (Φ), Young's modulus (E) and unit weight (ɣ) of geosynthetic encased stone columns.

08 September 2018 5,727 2 View

What is the most method to predict the settlement of foundation on heterogeneous soil reinforced with Stone Columns ?

What is the most method to predict the settlement of foundation on heterogeneous soil reinforced with Stone Columns.

07 August 2018 8,160 3 View

What is the best software to use for 3D modeling geosynthetic encased stone columns ?

I am looking for software that could be used in 3D modeling geosynthetic encased stone columns. Thank you.

06 July 2018 1,171 19 View

How apply boundary conditions in PLAXIS 3D ?

05 June 2018 2,098 3 View

How can i define properties of materials in FLAC 3D 5.0 ?

How can i define properties of materials and how apply boundary conditions in finite difference model FLAC 3D 5.0

04 May 2018 7,103 2 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

GC-MS retention index prediticon?

Hello experts, Does anyone know any free software about retention index prediction ?

08 August 2024 7,403 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

What precautions should be taken while handling S. aureus enterotoxin Type B in the lab?

I would like to understand potential safety concerns while handling SEB in the lab. Especially while working in animal house facility. Would like to know precautions for handling. Sigma MSDS...

07 August 2024 6,034 3 View