05 November 2018 1 8K Report

I want to know how adverse the effects will be when thermal coeff of expansion affects the printing process both in material as well as process .

More Aravinth Kamaraj's questions See All
How can we place the antenna with FSS in CST?

I design a unit cell of FSS. Now my doubt is how to design the full FSS structure using that unit cell and how to place my antenna with FSS like some of them in literature.

07 August 2023 9,410 2 View

How do we compare both simulated and measured results in single graph?

I have the simulated results and fabricated results. Now how do I combine and compare both the results in same graph like the graphs in journals.

17 April 2023 5,934 3 View

How to connect the SMAFEM connector in ADS?

How to connect the SMAFEM connector in ADS. I try to connect it directly with my design and run as momentum but it get joint with my design like a feed rather than connector. Than I try with fem...

14 March 2023 6,994 1 View

Stability analysis of dynamical systems can be studied by Lyapunov stability theory. How existence of solution is ensured in this case?

In Lyapunov stability theory, we are studying the dynamical character of dynamical systems without finding the solution of the considered system. But how the existence of a solution is ensured?

27 November 2022 7,614 2 View

NIH 3T3 transfection protocol?

Hi, Can anyone share their transfection protocol for NIH 3T3 cells. I tried with lipo3000 protocol. Very few cells are transfected and their shapes change after transfection.

29 November 2021 6,607 1 View

Is there a way for converting to graphics the legend in QGIS so that we can edit the text content in it?

In Arc GIS layout we can edit the contents in the legend of a layout by using the convert to graphics option and then ungrouping it. In the same way, is there any option is available in QGIS

16 November 2021 6,389 4 View

What will happen if we keep the at low temperature (100-200 K) cell after fixation?

For Fluorescence imaging after the transfection the cells are fixed and the protocol says that the fixed cells(within the coverslip) needs to be stored at 4o C. What will happen if we keep the...

10 October 2021 1,081 2 View

Non Linear analysis of a rubber Valve - Large energy error?

Hi all, I'm doing a non linear analysis using ansys. Total the assy contains housing,valve and a stopper. the housing and stopper are rigid material (PP/PC) and valve is silicone (shore 70 A)....

03 April 2019 632 6 View

Can someone provide me some good database/book for friction coefficient values of various Standard metals?

I want friction coefficient values of various standard metals such as EN10025-2 EN JS1072 UNS C27400 UNS C93200 UNS C95800 UNS C95800 UNS J02501 UNS S15500 UNS S31635 (EN 1.4571) I couldn't find...

03 September 2018 7,041 3 View

A question of MRF CFD simulation, I am getting a negative volumetric flow rate in my simulation. what does this mean?

I'm doing a CFD simulation of a commercial Ceiling Fan in a cubic room using MRF method, where i'm monitoring the torque ,volumetric flow rate. By seeing the volumetric flow rate results i'm...

13 June 2018 8,789 3 View

Similar questions and discussions
Can formaldehyd-fixed gelatin be melt?

I am puzzled about the properties of gelatin, when used for tissue-embedding. Hard gelatin can be melt again by temperatures about 40°C. Formalin-fixed gelatin is like crosslinked protein and...

07 August 2024 1,686 1 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Melt curve problem in qPCR?

Do these peaks in the curve indicate primer dimer or non-specific products?

01 August 2024 7,466 0 View

What is the best protocol for freezing the rat brain in preparation for protein detection by Elisa ?

What is the best way to freeze the rat brain - liquid nitrogen, Dry ice , isopentane - after isolation for later protein investigation by Elisa?

01 August 2024 1,722 1 View

How to Post-fix Mice pup's brains?

I need to Postfix mice brains. I slice the brains using microtome at 40 microns. These are Postnatal days 7, 11, 14, and 21. I am using half the brain for other analysis, so I need to fresh freeze...

31 July 2024 1,123 4 View

How to find a reaction is reversible or irreversible in CV? How to know the number of electrons transfer?

My screen printed electrode CV is given here. For Nerstean one electron reaction the delta E value should be close to 57 mV and ration of Ic/Ia should be close to 1. I did CV of my screen printed...

30 July 2024 4,671 3 View

CAD File of human's & rat's respiratory airways ?

Dear all, I am working on particle deposition in human's & rat's respiratory airways using CFD and I am looking for the 3D CAD file for my simulations (STEP or IGES format). If somone has such...

29 July 2024 1,092 2 View

Prevent sedimentation and maintain the suspension of powder particles in the resin ?

Hello, I am experiencing an issue with mixing micro powder with resin in a 3D printer. The problem is that sedimentation occurs after a short period (about half an hour to an hour). Could you...

23 July 2024 1,672 0 View

Cell optimization in 1D Nanotubes?

Dear All, I use Quantum Espresso. I want to optimize the structure of the carbon nanotube using the vc-relax. I got confused about how to fix cell_dofree here. For 3D, cell_dofree = 'all' or...

22 July 2024 5,708 0 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close