Hi.I have an extruder for dewatering a two phase fluid. I want to setup slip condotion in wall boundary condition in Ansys Fluent. how can I do that?

11 June 2019 1 8K Report

in wall boundary dial box I should specify the shear stress in three direction (x,y,z). how can I measure this shear stress? please help me....

Reza Goharimehr

This parameters related to the surface specifications. You should consider your materials properties and their shear stress between each other. Probably you find them in papers.

Badges
Science topic

More Hossein Najafi's questions See All

How to find the mean, SD and CI in SPSS?

Hi, I hope that someone can help me with this task: I have 5 groups of participants which are numbered in SPSS from 1 to 5 (according to their group number) and are all under the variable group....

03 March 2021 506 3 View

Do you know any MR image dataset?

I would like to research on MR images (0.5T and 3T). Can you please suggest some websites that I can download dataset including both 0.5T and 3T MR images? Thank you.

02 March 2021 7,735 3 View

What pH condition required to coat APTES on silica coated Fe3O4?

It's a hydrolysis reaction, which may produce by either acid or base-catalyzed reaction. so can anybody help me with this, which condition is suitable for this reaction?

26 February 2021 1,760 8 View

How to model Supercritical water gasification (SCWG) process in Homer software?

Hi everyone How to model Supercritical water gasification (SCWG) process in Homer software?

25 February 2021 4,075 1 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

What condition required for coating of Fe3O4@SiO2 by using APTES?

I tried coating Fe3O4@ SiO2 by using APTES in 5% water-ethanol but it is not coated. Kindly suggest a solution for it. Thanks

24 February 2021 5,992 4 View

Is it possible to define biogas as a fuel in the reformer process(scwg) in Homer software?

Hi every one Is it possible to define biogas as a fuel in the reformer process(scwg) in Homer software? Biogas fuel is not available in the options thanks

23 February 2021 6,518 3 View

How can I find the thermophysical properties of high temperature microencapsulated phase change materials (MPCM)?

Hi everyone. I am looking for a high temperature MPCM. More specifically, I need the thermo physical properties of a microencapsulated phase change material with the melting temperature between...

14 February 2021 3,606 2 View

How can I prevent bubbles from forming under a coverslip?

My colleague and I are having some trouble mounting 70 micrometer mouse brain slices. When we initially position the coverslip over the mounted slices, there are no bubbles but when we come back...

10 February 2021 3,580 1 View

Can explain this diagram to me, is this the average consumption curve for one day or the total consumption of days in a month summed up in specific?

The hourly load curves of the selected household in each season are shown in Fig. 28. Figure 28 shows the demand for electricity in four months on an hourly basis. Can you explain this diagram to...

08 February 2021 657 16 View

How to analyze a particular region of my simulation box in GROMACS?

Hi, I am using GROMACS 5.1.4 to simulate water in contact with a surface. I am only interested to calculate some properties of water near the surface. Let's say at a distance of x nm from the...

03 March 2021 9,989 2 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View