Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

How to calculate the annealing temperature of a primer pair?

I have to amplify a gene and my primers just reached. The Tm for Forward primer is 64.2, and that of reverse primer is 65.5. Can some one suggest how to get the best annealing temperature? Thanks...

01 March 2021 360 7 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

The reason that the culture of white fungi Contamination with green mold(Trichoderma), the culture autoclave at121 for 15 min. What is it?

Is the period to autoclave not enough? The inoculation in a hood and flame and UV and alcohol.

27 February 2021 9,356 3 View

How to include original NMR data in a manuscript?

hello. i am junior researcher. I received a comment from a reviewer that he could not find NMR data in my submitted paper. I had included the NMR graph with explanation and formula to calculate...

27 February 2021 734 4 View

Does different dilution factors affect negatively on NH3 reading ?

I have a sample of treated water sample & asked to obtain ammonia conc. in sample using a machine with 5-25 ppm detection range. However, upon testing with different dilution factors, all...

27 February 2021 8,483 3 View

Can anyone share his experience regards Smoothing in origin?

I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...

26 February 2021 8,183 3 View

No title

01 March 2021 3,905 5 View

What test should I use to compare two or three means, if data is not normally distributed but sample size is > 30 in each group?

I personally feel this as a most confusing question. As per my understanding, if sample size is > 30, and sample is skewed, we can still use paramteric approach, as it will follow Z...

01 March 2021 1,587 6 View

What do I do with DLS peaks that are from the buffer?

I'm looking at the aggregation of my protein sample using DLS. Unfortunately, my buffer (20mM HEPES) also results in a set of peaks. These are at approximately 1 and 1000 d.nm. The lowest peak...

01 March 2021 9,015 2 View

Sample size determination for non-parametric tests?

How do I run a a priori sample size determination for non-parametric tests, like the Mann-Whitney U-test and the Kruskall-Wallis or other non-parametric tests that accord with the unpaired t-test...

24 February 2021 166 6 View

How to determine a priori sample size for t-test with unequal means?

I need to conduct a a priori sample size determinations for t-test with unequal means, but I don't know the sizes of the groups nor the ratio of both groups... Can I do a sample size determination...

24 February 2021 8,289 3 View

What are alternatives to factor analysis for a small sample?

My sample size is too small to conduct a factor analysis. I created my own psychometric scale for measuring Effectiveness of Support, which contains 38 items (4 sub-scales) Im really struggling...

23 February 2021 9,287 12 View

Missing Data in Pretest and Post test- Experimental Research design?

Hello all, I am analyzing some pretest and post-test data that were given to evaluate knowledge of targeted vocabulary before and after the intervention. Pretest and post-test are identical and...

23 February 2021 9,400 7 View

Is there any software or formula for sample size determination by using sensitivity and specificity?

I want to conduct research on the diagnostic performance of some tests. I want to calculate sample size by using the sensitivity and specificity of the test in the previous studies. So Is there...

23 February 2021 619 5 View

What low-cut filter (high Pass frequency) to be used for response spectrum (Tripartite plots) ?

What low-cut filter (high Pass frequency) to be used for the response spectrum (Tripartite plots)? I am currently working on differentiating between hard/soft site responses in Indo-Gangetic...

21 February 2021 9,273 2 View

Statistical Tests for Quantitative Study?

Hello Everyone, I have one population, sample size 200. and needed to find the correlation between Variable A and B. Also, which T-test should I choose for hypothesis testing Please advise...

21 February 2021 7,591 4 View