GDI engine injection duration, injection quantity and rail pressure?

07 July 2018 0 7K Report

Dear all

Can anyone provide me the details of fuel injection duration, injection quantity and rail pressure at which a GDI engine operates at full load, part load and idling conditions. I am in need of the above details in the selection of a right injector. Can anyone help me in this regard.

Badges
Science topic

Similar topics
Thermodynamics
Pressure

More Jubin V Jose's questions See All

What is the ideal CA50 location for SI engine?

CA 50 - 50% burn (crank angle) from a 'rate of heat release vs crank angle' curve for a given...

09 October 2018 293 1 View

Increase in fuel temperature before injection in GDI?

Dear all I wish to know what is the rise in temperature of the fuel compared to the ambient temperature once it leaves the fuel injector nozzle in GDI. The temperature increase can be due to...

06 July 2018 4,895 1 View

Radar sensors availability?

Dear all I wish to know whether any one is working on Radar system for autonomous vehicles. I wish to know who is the supplier of the same. I need only a few systems. Can i get any system that...

02 March 2018 5,198 5 View

Basics of internal combustion engines?

Beginners can use this for understanding the basics. http://www.iitg.ernet.in/scifac/qip/public_html/cd_cell/internal_combusn_engines.htm

02 March 2018 2,914 0 View

Earth core is it a future energy source? Solution for all energy crisis! ?

We all know that earth core is at very high temperature. Is it possible to extract that energy out from there? Geothermal as of now the technology is not well mature enough as per my opinion....

01 February 2018 4,394 4 View

Can vibration induce turbulence in a laminar flow?

I read in one fluid dynamics text that flow can remain laminar even up to 8000 to 10000 Reynolds number when it flow through a pipe. If the medium is undisturbed and surface is smooth enough. So i...

01 February 2018 8,653 22 View

Can anyone suggest good papers or books on in-cylinder flow in IC Engines?

I wish know in detail about 1. In cylinder turbulence pros and cons. 2. Effect of tumble. 3. How to analyze the vortices formed and its effect? 4. Velocity vectors and its importance. 5. Flow...

01 February 2018 6,574 0 View

Turbulent kinetic energy in IC Engines?

Hai can anyone suggest me a simple and good book/paper that can give me more insight into turbulent kinetic energy in IC engine related studies.

31 December 2017 3,653 2 View

Reason for higher stability or lower COV of CI engine compared to SI engine?

CI engine use to give stable torque output and lower cylinder to cylinder variation. Can anyone suggest me reasons for the same.

31 December 2017 8,427 2 View

How to avoid signal interference in forward collision control system?

We will be having cars with forward looking radar or ultrasonic sensors which will look for obstacles in a car. If two signals from 2 cars interfere and if it result in wrong estimation of value...

31 December 2017 615 3 View

Does the pressure(-600 mmHg) affects pH?

When I conducted the degassing experiment using decompression under anaerobic condition(and I used ferrous based chelating agent), the oxidized ferric were observerd. So, could you tell me the...

03 March 2021 4,892 5 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

Is there any test to determine the cardiovascular risk of patients with obesity? from the perspective of obesity?

We found tests to determine cardiovascular risk taking into account lipid profile, blood pressure, age, history of diabetes, other laboratories. But when weight is involved, there is a paradox. I...

02 March 2021 6,036 1 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

Sutter electrode holder leaking after applying positive pressure. How to fix?

I am using a Sutter electrode holder for my patch clamp experiments, but I'm having trouble keeping positive pressure inside my electrode due to a leak out of the back of the holder. I have added...

02 March 2021 5,829 1 View

What SPSS analysis should I run with one IV (with two levels) and two DVs?

Hi, I am trying to figure out which test would be most appropriate to run for the following question: Is there a difference in task blood pressure between smokers and non-smokers? There are two...

01 March 2021 8,235 2 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

Trouble with Charting with Google Earth Engine (Technical)?

Hello. I have a problem with the charting in google earth engine. I created an image collection by combining 5 image collections of five parameters and using ee.Join.inner ( ) and .apply ( )...

26 February 2021 7,084 2 View