For wavey plate did the conduction heat transfer will be the same for flate plate?

More Vinous Hameed's questions See All

Area of heat conduction calculation if it is not constant?

if the cross sectional area of heat transfer is change with the length of the plate; how can i substitute its value through the calculation procedure. can i use average value for different cross...

05 June 2018 6,948 0 View

what is the best method to fit a thermocouple on a plate or a tube ?

if any one can help? the best method for fitting a thermocouple on a flate plate or cylinder without affecting the conuctivity of the materials and the flow of the fluid? did the the probe of the...

03 April 2018 3,840 6 View

Mixed convection system?

for mixed convection system( free + forced ) how i can calculate and measure the effect of each one separately?

02 March 2018 5,883 2 View

How we calculate the area of heat transfer for different perforation shape?

how we calculate the area of heat transfer for different perforation shape? did the equivelent area works here? how it effect on a calculation? is there any correction factor for it?

01 February 2018 8,060 4 View

Waters 2707 HPLC autosampler problem?

I am using a 2707 waters HPLC device. When I try to inject a sample, it says missing plate or rack. I changed the needle and calibrated its position but I still get the same problem. I even get...

02 March 2021 1,408 1 View

Should we change media after1st 6hrs after plating HUVEC bought from INVITROGEN?it's not recomended by invitrogen.Will DMSO present in stock matter?

We have HUVEC bought from Invitrogen. Cat no -C-003-5c. while first plating the cells we have bought the protocol suggests not to centrifuge the cell with media to remove the DMSO. Should we...

02 March 2021 3,713 2 View

How to normalise data on OPM package from R Studio ?

Good afternoon, I recently used OmniLog from BIOLOG for my experimentations : I tested the metabolism of different strains on 2 types of plates. I have 16 strains of 3 different groups...

02 March 2021 3,584 1 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

PUC19 as a transfer plasmid for lentiviral delivery?

Hello, Is it possible to use pUC19 as a transfer vector to be packed in using the second generation viral particles packaging system( pMD2.G; psPAX2 plasmids)? As far as I understand it there is...

28 February 2021 4,868 2 View

Benefits of the 24 welled plate?

We have always used the 96 welled plate, the 48 welled plate but apparently there is much evidence on the 24 welled plate and above all its benefits.It states it is the same you would use on ELISA...

28 February 2021 1,149 1 View

Can bacterial suspension be pipetted directly onto petri dish and agar poured onto it?

Hi, recently I encountered a protocol for plating which was not the usual method I have been practicing (pour LB agar onto plate, allow it to solidify, pipette bacterial suspension onto plate,...

28 February 2021 7,292 3 View

Naseem Ali

Check these articles

"The CFD Simulation Study on the Fluid‐State of a Wavy Plate of Evaporative Condenser"

"The Effects of Wavy Plate Phase Shift on Flow and Heat Transfer Characteristics in Corrugated Channel"

Md. Washim Akram

Conduction heat transfer depends on the following factors as far as I know,

1. Micro-structure of metals

2. Different metal defects

3. Path of heat transfer

As far as I think, depend on this factors the conduction heat transfer rate for flat plate is higher than wavey plate for same surface area.

Vinous Hameed

thanks Md. Washim Akram for your answer but how can you proof it by calculation