How we calculate the area of heat transfer for different perforation shape?

More Vinous Hameed's questions See All

Area of heat conduction calculation if it is not constant?

if the cross sectional area of heat transfer is change with the length of the plate; how can i substitute its value through the calculation procedure. can i use average value for different cross...

05 June 2018 6,948 0 View

what is the best method to fit a thermocouple on a plate or a tube ?

if any one can help? the best method for fitting a thermocouple on a flate plate or cylinder without affecting the conuctivity of the materials and the flow of the fluid? did the the probe of the...

03 April 2018 3,840 6 View

For wavey plate did the conduction heat transfer will be the same for flate plate?

what is the difference when we calculate the conducted heat transfer for flate plate than the wavey plate both have the same surface area?

02 March 2018 1,921 3 View

Mixed convection system?

for mixed convection system( free + forced ) how i can calculate and measure the effect of each one separately?

02 March 2018 5,883 2 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

PUC19 as a transfer plasmid for lentiviral delivery?

Hello, Is it possible to use pUC19 as a transfer vector to be packed in using the second generation viral particles packaging system( pMD2.G; psPAX2 plasmids)? As far as I understand it there is...

28 February 2021 4,868 2 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

Anyone that can help with Maxquant TMT16plex which is missing?

Hi I am very new to proteomics analysis. I have got raw files from core facility running thermofisher TMT 16plex 4 hours. I cannot find on maxquant the option TMT16Plex there is only up to 11...

25 February 2021 1,675 3 View

How to properly calculate the fluid solid heat transfer between polypropylene matrix and glass fiber in a porous medium?

I'm building a cfx model of thermoplastic pultrusion process on ansys and i have a doubt on how is the proper way to set this parameter in a porous medium

24 February 2021 1,915 1 View

Hayder Jaffal

Dear Dr. Vinous

Either the heat transfer area is equal or the hydraulic diameter of perforated is the same for the purpose of comparison in the thermal performance of different perforation shapes.

Naseem Ali

The hydraulic diameter could be useful for your case.

Mahesh Kumar

Dear Hameed if you elaborate a bit more your research problem then I think you may get the right answer. However as per your query in my opinion equivalent area will also work for the analysis purpose.

Ali Benhmidene

http://www.j-mst.org/On_line/admin/files/15-032_1945-1951_.pdf

https://irjet.net/archives/V3/i4/IRJET-V3I4616.pdf

http://eprints.whiterose.ac.uk/87729/1/PFHS_accepted.pdf