Extract Reflected waves from incident waves?

More Aydin Amini's questions See All

Plasmonics as a collective oscillation of holes instead of electrons?

In metals, the outermost conduction electrons (electron plasma) interact with incident photons and according to the classical Drude model, they may resonate and build up longitudinal plasmonic...

31 December 2019 2,965 6 View

Hopping oxygen and metastable donor state ?

Can anyone explain how an oxygen ion hopping in illuminated thin film IGZO, results in a metastable donor state?? and how this donor state can lower the e-h recombination in that film?

11 December 2018 6,587 6 View

The contribution of electrons and lattice vibration in thermal conduction of metal?

In the solid, specially metals, the thermal conduction can be done with lattice fluctuations and free conducting electrons, where the role of electron is more significant. I want to show the...

09 October 2018 7,264 3 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

Samples to study circular dichroism (chirality)?

I want to build a low-cost polarimeter to study circular dichroism (chirality). What type of samples can I use? I am looking for samples that can be found outside the laboratory.

01 March 2021 9,101 3 View

How to remove DCU and HOBT from my reaction?

I am doing a acid and a chiral amino alcohol reaction using DCC and HOBT in DCM or THF? Can anyone suggest me how to remove DCU and HOBT from a reaction mixture??

28 February 2021 2,153 1 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

How to use measure capacitance change in COMSOL time dependent study ?

I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...

26 February 2021 8,567 3 View

Error in comsol?

Dear respected researchers, while performing CFD analysis in Comsol it's showing like this Error: Nonlinear solver did not converge. The maximum number of Newton iterations reached can...

24 February 2021 249 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

How can I find the effect of different parameters like (Reynolds number, Hartman number, volume friction etc.) in COMSOL?

Here I am facing this problem. I don't find any effect of this type of parameters. I am a beginner user of COMSOL.

23 February 2021 9,086 3 View

How to Implement Elastoplasticity in a PCL model in COMSOL Multiphysics?

I am using COMSOL Multiphysics 5.5. I am trying to simulate the tensile test of PCL scaffolds. However, regardless of the strain, I have the elastic region all the time which is not true when it...

23 February 2021 4,050 1 View

Milo Hyde

I know very little about Comsol but if it returns the total field, i.e., the incident plus reflected, you could subtract the known incident field from the Comsol result to isolate the reflected/scattered field.

Aydin Amini

I'm really thankful that you have considered my problem. Actually, COMSOL gives the total field as a result and I don't have any access to mode profile...