How to model Supercritical water gasification (SCWG) process in Homer software?

Hi everyone How to model Supercritical water gasification (SCWG) process in Homer software?

25 February 2021 4,075 1 View

Is it possible to define biogas as a fuel in the reformer process(scwg) in Homer software?

Hi every one Is it possible to define biogas as a fuel in the reformer process(scwg) in Homer software? Biogas fuel is not available in the options thanks

23 February 2021 6,518 3 View

How can I measure the surface interaction or surface interfacial chemistry between polishing abrasives and upper surface of substrate ?

I am working on polishing abrasives. I need to do few characterizations ? which can provide the on time surface chemistry of substrate with polishing abrasive during optical polishing. I would...

18 February 2021 5,319 3 View

How can I find the thermophysical properties of high temperature microencapsulated phase change materials (MPCM)?

Hi everyone. I am looking for a high temperature MPCM. More specifically, I need the thermo physical properties of a microencapsulated phase change material with the melting temperature between...

14 February 2021 3,606 2 View

Can explain this diagram to me, is this the average consumption curve for one day or the total consumption of days in a month summed up in specific?

The hourly load curves of the selected household in each season are shown in Fig. 28. Figure 28 shows the demand for electricity in four months on an hourly basis. Can you explain this diagram to...

08 February 2021 657 16 View

How to conduct mesh sensitivity/convergence analysis in MSC Marc Mentat?

Currently using Msc Marc Mentat for FEA. Now i conduct the mesh convergence/sensitivity analysis manually. So I need to know if there any automatic way to conduct the mesh convergence/sensitivity...

04 February 2021 3,310 3 View

Why VASP MD Crashes with ALGO = Fast ?

Hi, I'm doing molecular dynamics on a 168 atoms system with a 20 A vacuum. To speed up my calculations, I set ALGO = Fast tag in INCAR, but surprisingly VASP crashes momentarily!. I have done a...

25 January 2021 9,876 3 View

How to measure the size of simulated/generated Fields(Magnetic or Electric)?

Hello everyone, I'm a beginner on the simulation software ANSYS HFSS. I need to know how to measure the size of the generated field of my simulation. I have simulated a geometry that looked like...

20 January 2021 9,113 2 View

What is the best way to calculate electrical conductivity of semiconductors and the same system with a layer of oxide using Quantum Espresso?

I have tried BoltzTrap, and EPW but I'm not sure whether Boltzmann Transport Equation is a right approach for a complex system (semi cond. + an Oxide layer or even the semiconductor itself). Also...

11 January 2021 4,597 4 View

What is the gradient thermal annealing (GTA) process?

Hello to all What is the gradient thermal annealing (GTA) process?

06 January 2021 7,740 2 View

Does any one know how i can prepare liver tissue with transmission electron microscope with good fixation?

i have problem in preparation of liver tissue with bad cell organelles and how i can adjust osmolarity

03 March 2021 8,890 1 View

I need to image mesoporous silica nanoparticles that are in ~100 nm size and do high resolution TEM to look at mesopores. what grids should I use?

Need to image mesoporous silica nanoparticles using the TEM. Also, need high resolution TEM images to see the mesoporous structure. Kindly suggest what kind of grids to use. Thanks, Shatadru

02 March 2021 1,787 2 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Shall I skip the measurement model in SmartPLS?

Hello everyone, I had run a mediation model in SmartPLS using questionnaires that were already validated among my statistical population. A professor who edited my paper -though she is not...

01 March 2021 3,052 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Does anyone know to clarify these changes?

01 March 2021 1,290 2 View

In an eye with Tyndall, does each dot correspond to an individual cell?

When you observe the presence of Tyndall in an inflamed eye: Does each of the small floating dots correspond to an individual cell or to an aggregate of cells? Does a conventional slit lamp have...

27 February 2021 6,326 2 View

How to calculate the crystallinity of cellulose film?

27 February 2021 2,753 4 View

SEM or Multiple Regression for an analysis without Latent Variables?

Hello, I have three hypothesis to test, all with the same IV. I am testing if the effect of the IV on the first DV is mediated by awe. I am then measuring whether the effect of the IV on a...

26 February 2021 8,399 5 View

What could be the reason for not having further low chi square value (better agreement) in my refinement result?

I have tried every combination of parameter changes and after that i have a poor chi square value. I can't get it lower any further. I know there have been a lot of discussion about Rietveld...

26 February 2021 8,480 3 View