Does the oxidation of the surface of carbon nanotubes affect their phothermal conversion ability?

More Ana Luísa Daniel-da-Silva's questions See All

Despite single-cell RNA, how can I characterize a new cell subtype/phenotype?

A new cell subtype was found out only during regeneration phases after a cuprizone-induced demyelination model. How can I characterize this cell? It is important to highlight that was already...

13 February 2021 1,245 1 View

Permanent Fluid temperature initialization in Ansys Fluent?

Dear researchers, I am coupling Design Optimization with ANSYS Fluent in Workbench 2020 R2. I can do the analysis. I am patching the initial Temperature values of the zones. However, the patch...

28 January 2021 4,265 2 View

Luciferase assay for miRNA-gene: How to obtain DNA (PCR product) from the mutated primer?

To perform the Luciferase assay for microRNA-gene interaction its necessary a primer (wild-type) to amplificate the specific ligation site and also a mutated primer. But if your primer has a...

19 January 2021 8,568 3 View

Which peak should I consider when calculating ZIF-8's crystalline size from XRD?

Hello, Using the Scherrer's equation, one could calculate, roughly, the crystalline size of ZIF-8. However, I am confused as to which peak in the XRD pattern should be taken for the calculation?...

10 January 2021 8,633 3 View

How to couple Moldex 3D with MATLAB for design optimization of an injection mould?

Hello, I would like to use the software Moldex 3D for the design optimization of an injection mould. How can I couple Moldex 3D with a MATLAB code? Any help appreciated, I wish you all a happy...

09 January 2021 569 2 View

How to setup ANSYS Fluent for simulating the filling stage of an injection mould?

Hello, I am using ANSYS Fluent for simulating the filling stage of an injection mould. However, when comparing the results with those of specialized software, such as Moldex 3D, I found the...

07 January 2021 7,992 1 View

Which plants and trees have the best ability to prevent the entry of particulate matter (PM2.5 and PM1) and nanoparticles in indoor environments ?

In recent years our group has highlighted the importance of trees and plants in public and recreation parks in large mega cities. However, we are interested in developing "green shields" to be...

05 January 2021 6,500 3 View

How to phosphorylate specific residues on pymol?

Hi everyone, I am using the pyTMs plug in on Pymol to phosphorylate a particular threonine in my protein. I am having difficulty in selecting only one or two residues - it seems I can only...

05 January 2021 230 3 View

How to perform Potential Surface Energy Exploration (PES) calculations?

I would like to receive help, as I am trying to make an analysis of the ethanol PES, but the calculations are always giving error. I use the conda-forge version of xtb (* xtb version 6.3.2...

04 January 2021 602 2 View

How do you create a funnel plot in STATA to assess publication bias using proportions from the metaprop command (for a meta-analysis)??

Hi everyone! I am trying to use STATA to create a funnel plot to asses publication bias using proportions from studies for a large meta-analysis (having used the metaprop command). I"m having...

09 December 2020 6,096 3 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

I need to image mesoporous silica nanoparticles that are in ~100 nm size and do high resolution TEM to look at mesopores. what grids should I use?

Need to image mesoporous silica nanoparticles using the TEM. Also, need high resolution TEM images to see the mesoporous structure. Kindly suggest what kind of grids to use. Thanks, Shatadru

02 March 2021 1,787 2 View