Does someone know which is the best method to produce great quantities of nails for horseshoes?

More Daniel Martinez Krahmer's questions See All

Sheet steel laser cutting?

If you have a laser cutting machine that can cut a steel sheet up to 10 mm thick, is it possible to cut a 20 mm steel sheet in two consecutive passes? If the answer is yes or no, why?

09 October 2019 9,436 3 View

Lubrication regimen in pin on disk test?

I know that a way to establish the lubrication regime in a pin on disk test is by measure the resistance between the pin and the disc. Some papers say that if the resistance is of 2 ohm, the...

05 June 2019 7,949 3 View

How to create a mechanical engineering graphical abstract ?

Hi People. Here in RG there is a similar question but for works in biology. Some of you know if is there any software available to design mechanical engineering graphical abstracts ? Something...

31 December 2018 3,587 2 View

Warm forging of SAE 1045 steel?

Hi People. I need to know the temperture range for making warm forging of SAE 1045 steel.

31 December 2018 4,719 0 View

Hot forging dies made by SAE H13 tool steel?

Please. I need to know what level of hardness provide a equilibrated behaviour between wear resistance and toughness. Also, if a ionic nitriding treatment reduce the friction factor between the...

10 November 2018 6,622 1 View

Redes neuronales artificiales?

Esta pregunta es solo para los amigos y amigas de RG que hablan español. Les quiero preguntar si me pueden recomendar, al juicio de cada uno, cual es el mejor libro en ESPAÑOL para poder aprender...

09 October 2018 8,917 0 View

Turning of low carbon steel?

People. I need your colaboration. What value of hardness do you think is the minimal to not worsen the maquinability level of the steel? I work with steel of 0,1% C. I some of you have a paper, is...

08 September 2018 9,430 3 View

How do I assess ignition risk during magnesium turning?

Some people say that the risk is bigger when the chip particles size are 500 micrometers or minus? What is the reason of this size?

07 August 2018 7,725 0 View

Recrystallization temperature of one steel?

Please. I need information about the recrystallization temperature of SAE 1010 steel, and also the temperature range for warm forging.

05 June 2018 5,844 3 View

Grinding ball manufacturing by hot rolling process?

Hi People. Please, I need to know which is the best material to make the guideline plate in a hot rolling grinding ball machine. Here the is a link to see the...

02 March 2018 832 6 View

How to select target material for X-Ray generation?

Generally, the target material is Mo, Co, Cu, Fe, Cr, etc, so on what basis should we choose this material?

31 July 2024 5,824 0 View

What is the solubility of Iron (+3) in Bismuth Oxide?

Dear all: I am modifying Bismuth Tungstate with Hematite (Fe2O3), so I would like to know about how much Iron(+3) can form a solid solution in a Bismuth Oxide matrix. Best wishes Marco

29 July 2024 2,163 1 View

How should operational parameters be selected when developing a pore-free laser welding technology?

There are three operating parameters - the laser power, the diameter of the focus spot and the scanning speed. It is necessary to obtain a seam of a given depth without pores. What parameter...

27 July 2024 7,168 2 View

Is it true that there is a physico-statistical meaning to the constant π other than circular geometry but the iron guardians of the SE deny it?

We assume that there is a physico-statistical meaning to the constant π other than circular geometry, but the iron guardians of the Schrödinger equation deny this. The iron guardians of the...

22 July 2024 4,285 9 View

Is there a good macro photography kit for on-site metallurgical investigation?

I am looking to purchase a photography kit for onsite metallurgical investigations, such as capturing photos of worn areas, hot tears, cold tears etc. Could anyone suggest me a good...

22 July 2024 3,490 2 View

What could be the possible reason that sintering of polycrystalline diamond fabricated with tape casting has suddenly started failing?

I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...

16 July 2024 3,212 5 View

What binders suggestion that I can use for zinc alloy?

I am working on powder metallurgy, and during the compaction process, the powder does not pelletize and remains in its powder form. To address this issue, I am considering using binders to improve...

13 July 2024 9,003 2 View

Can an average household DIY spot welder be used for pouch cell electrode tab?

Would an average spot welder suffice for welding tabs for pouch cell electrodes instead of an ultrasonic one? Why would an ultrasonic welder be better than a regular spot welder?

10 July 2024 8,763 0 View

Surface adsorption with the help of iron and UV/H2O2 is innovative?

1.The topic I am going to research is "Advanced Gray Wastewater Treatment Output from the Biological Process by Iron-assisted surface adsorption and UV/H2O2". I think this method has been used a...

08 July 2024 9,464 1 View

What can be done when electronic minimization does not converge during geometry optimization in CASTEP?

Hello All, I've been facing difficulty in executing geometry optimization of a sodium polyanionic phosphate (Na4Fe3P4O15) crystal in CASTEP (please find the input and output files attached). When...

07 July 2024 8,626 2 View