Does it possible to prepare the metal sulfides thin films, particularly the substrate temperature fixed at 400 c?

08 August 2016 1 2K Report

because the melting Point of the sulphur is low. In this case If we fixed the temperature of the substrate at 400 c, it may affect the formation of sulphide.

Alain Kassine Ehemba

Dear Diwakar,

It depends of the method of eleboration you use. What method you want to use for this elaboration?

If the temperature of the substrate is lower you can use methods without evaporation like elctrodeposition.

Badges
Science topic

More Diwakar Karuppiah's questions See All

What is meant by annealing?

Temperature

04 May 2018 7,889 3 View

What is the major difference among charcoal, graphite, graphene and activated carbon?

Graphite is 3D Graphene is 2D charcoal and activated carbon

03 April 2018 5,583 4 View

Is any bacteria which affect the inoraganic maertials?

the materials like metal oxide, metal nitrate etc.

31 December 2015 5,756 2 View

Which type of compound does lamda max of 218 indicate in a uv-vis spectrum of a partially purified compound through column and TLC?

A crude extract of fungal culture using EtOH was subjected to column and TLC and partially purified compound was obtained. UV vis spectrum of the compound/s has max absorbance at 218nm. The...

11 August 2024 9,801 2 View

Aspen Plus Simulation?

Greetings When one is to perform Simulation or modelling of Pyrolysis of Biomass Waste materials using Aspen Plus software, and one has both the macromolecules breakdown (Cellulose, Lignin and...

06 August 2024 5,023 1 View

How can I measure the thickness of thin film by Uv-Vis?

06 August 2024 7,810 3 View

Why is TLC not a form of partition chromatography?

Why is TLC not a form of partition chromatography and paper chromatography not a form of absorption chromatography?

03 August 2024 7,035 3 View

Is there a good freeware software for photodocumentation of TLC?

I need something like Camag's VisionCat software for photodocumentation of TLCs. Could you recommend something?

31 July 2024 8,415 1 View

How to build my own lab made four point probe set up?

Hello, I'm trying to measure the conductivity of semiconductor films but since I don't have a commercial four point probe set up I would like to build one on my own in my lab. I have generators,...

30 July 2024 906 2 View

Does anybody know why my chitosan/pva/gelatin hydrogel dissolve in PBS?

My final research is about making chitosan/pva hydrogel for wound healing using gelatin as crosslinker. Last month, i made the thin film hydrogel and it turn well. It was okay. Last week, i make...

28 July 2024 2,794 6 View

What plants have high levels of sulfur-containing amino acids such as methionine?

Methionine, cysteine, homocysteine, and taurine are the 4 common sulfur-containing amino acids, but only the first 2 are incorporated into proteins. Sulfur belongs to the same group in the...

22 July 2024 4,273 4 View

Is it possible to manufacture polypropylene sheets using a biaxial process?

I know that films and other low-thickness laminated products are produced using biaxial orientation, but is there something similar for sheets with a thickness of around 6 mm? Or are they...

21 July 2024 1,559 1 View

How do you decide an optimal AC amplitude for non-faradaic electrochemical impedance spectroscopy?

I work with planar interdigitated electrodes (IDEs). The finger width and the spacing between the fingers are 5 micron. The surface of the IDEs is coated by a non-conductive polymer layer...

16 July 2024 5,031 1 View