I mean to ask, is it right to say that a solid element behaves exactly like a beam element, given the same cross section, simply supported boundary conditions etc?
I am talkingin terms of maximum deflection and bending stress.
Hello everyone, I am thinking how the function should look like in order to generate this kind of curve shown below. I am guessing the variables should be : the radius that increases by "x"...
08 September 2019 5,518 3 View
Hello everyone, In Abaqus, my model uses shell elements. After the simulation when I try to compare the principal stresses, there are 4 possibilities : 1. Max In-plane Principal 2. Max...
08 September 2018 5,736 3 View
Hello everyone, In my model (predominantly rubber), I get a maximum strain of around 15% compared to the initial state. I have experimental data for the rubber compound I am using, and I want to...
07 August 2018 3,292 3 View
Hello everyone, I would like to know how to view the beam section forces in the axial direction of the beam. I have selected SF in the output field variables, and am not sure if SF1 means axial...
06 July 2018 1,633 2 View
Hello everyone, I have a cylindrical (non-uniform) model as shown in in the figure. I would like to assign the orientation such that : Z-axis = normal to the surface X-axis = along the radial...
05 June 2018 2,862 3 View
Hello Abaqus users, I am looking for the best way to model a yarn-knitted reinforced rubber hose in Abaqus, in order to measure the expansion and burst pressure. I have modeled the 3D geometry...
05 June 2018 4,039 0 View
Hello everyone, Does anyone have any experience/insight on RVEs where the fibers interlock, thus causing some contact to occur between the fibers of the matrix? Please do let me know whatever...
05 June 2018 4,939 2 View
Between and Elastic-Isotropic model with a low young's modulus, and a Hyperelastic Material that fits best with experimental data, what model (overall) gives relatively good results with less...
05 June 2018 1,132 3 View
I have searched on google and in the abaqus manual, but there is very little information on this topic. I would love to see some example subroutines.
05 June 2018 4,657 17 View
Hello everyone, I plan to model a knitted reinforcement within a rubber hose in Abaqus in order to analyse the various stresses sustained by them during hose expansion. I am wondering whether to...
04 May 2018 6,387 8 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
What should be the equation for halfway bounce back boundary condition for flow field with forcing term?
08 August 2024 7,938 1 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...
07 August 2024 1,937 1 View
I am puzzled about the properties of gelatin, when used for tissue-embedding. Hard gelatin can be melt again by temperatures about 40°C. Formalin-fixed gelatin is like crosslinked protein and...
07 August 2024 1,686 1 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
Hi, we have measured tryptic peptides using both DDA and DIA method on QExactive. In DDA replicates i saw unusual intensity drops occurring at the same sections of chromatograms in DDA replicates...
07 August 2024 3,218 4 View