Does anyone know NIST Evap-Cond V.3.0 circuity design program?

11 November 2014 1 956 Report

I would be grateful if you could share any experiences and knowledge about using NIST Evap-Cond V.3.0 circuity design program. I didn't create non uniform airflow profile in program. Thank you in advance.

Ergin Bayrak

Thank you very much for helping Dear Mrs. Tsambani.

Badges
Science topic

More Ergin Bayrak's questions See All

How can we ensure the better temperature measurement on the stainless steel microtube?

We are gonna built an experimental setup about the flow of supercritical CO2 under constant heat flux in stainless steel circular microtube (0.5 mm diameter and 300 mm length). It will be placed...

08 September 2019 2,062 5 View

How to model compressible supercritical fluids by using large eddy simulation method?

When the buoyancy effect is significant in supercritical fluids passing in the tube, some eddies can form in any location of tube, especially at the vicinity of supercritical temperature. So, what...

07 August 2019 10,008 2 View

How can we make the connection of teflon insulator to the experimental setup?

We have been trying to build a new experimental setup in order to investigate the thermal-fluid characteristics of supercritical CO2 in the microtube. We want to be sure that everywhere of test...

02 March 2019 2,944 1 View

What is your pump manufacturer recommendations, ensuring low flow rate and high operating pressure?

We have recently designed an experimental setup to investigate the detailed thermofluidic mechanism of near-critical CO2. We need to pump, ensuring low flow rate, high operating pressure and also...

06 July 2018 6,618 4 View

What are the current problems in near critical CO2 condensation?

Hi, I have recently been trying to define my Phd topic in the field of near critical CO2 condensation in small scale channels. We have a CO2 test rig, which can be performed the performance test...

01 February 2018 5,289 1 View

What is the method of O-grid forming in corrugated surfaces?

I have a rectangular microchannel. There is some corrugated protrusion at the local area of this channel. I couldn't form the boundary layers with O-grid (in ICEM CFD)to this corrugated...

08 September 2017 3,188 0 View

What are your recommendations to solve numerical thermal-fluid problems of narrow channels ?

Nowadays, I have been modelling a 3-D cooling plate including rectangular water channels (height=1 mm, width=0.5 mm) for Li-ion battery via Ansys Fluent. Also, there are the different type of...

05 June 2017 8,995 4 View

What is the reading error of frost thickness measurement?

I have captured photographes at windward of fin and tube heat exchanger during frosting test and processed these images via Matlab Image Processing Toolbox and determined frost thickness value by...

04 May 2016 4,939 1 View

Is it possible to identify optimum refrigerant distributor geometry by building a water-vapor mixture test set-up?

Hi Dear Colleagues, As you know, refrigerant two phase distribution at evaporator is big problem because of the fact that it can cause significant capacity reduction unless used optimum...

10 November 2015 8,571 1 View

What is the precautions to avoid the negative effects of hydrogen sulphide on heat exchanger copper fin?

Dear collegues, I have been researching the damage of H2S on copper fins and precautions that have to be taken. What is the max. recommended H2S ppm in the air inlet of heat exchanger to not occur...

07 August 2015 1,087 3 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

GC-MS retention index prediticon?

Hello experts, Does anyone know any free software about retention index prediction ?

08 August 2024 7,403 2 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

Are air moisture harvesting technologies effective in combating desertification?

Air moisture harvesting Air water collection devices

06 August 2024 5,473 2 View

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

Research Methodology - Impact of Corporate Reputation on Stakeholders Behaviors?

Please can anyone support with the survey questions based on RQ measures and propose how to do it in FMCG industry and include as well the role of brand equity Thanks

06 August 2024 949 0 View

Anyone having idea about VN primer for miRNA primer design ?

How to design VN primer to attach with universal reverse primer

05 August 2024 2,116 3 View

What should I do with parameters that are not relate to my simulation in MyLake model?

I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?

04 August 2024 1,537 1 View

Can anyone provide me with molecular docking softwares/ websites?

Molecular docking software/ websites?

02 August 2024 8,704 7 View