19 February 2014 1 2K Report

EPA recently revoked the annual PM10 standard, while California has kept it. Any comments on this decisions?

More Pablo Ruiz-Rudolph's questions See All
How to explain the different interaction between soluble and insoluble polymer in water?

Hello everyone, I am try to understand the differences interaction between insoluble and soluble polymers in water with metal ions and how theit charge density (of metal ions) affect the interaction.

29 July 2024 6,350 3 View

Is this cell cycle analysis correct?

When I applied the cell cycle algorithm to these two samples in FlowJo, I encountered some concerns regarding the accuracy of the fit. The images include both a control and an apoptosis-inducing...

18 June 2024 1,984 0 View

Two Professor Positions at The Institute of Geography?

Two associate professor positions: The Institute of Geography of the Pontificia Universidad Católica de Valparaíso, Chile, has opened two competitions for associate professors in the subjects...

11 June 2024 5,547 2 View

How Artificial Intelligence (AI) can change the way to write a thesis?

How Artificial Intelligence can change the way to write academic thesis under master and Pd.D. levels are affecting the originality and knowledge of future academics.

09 June 2024 1,156 9 View

Would the concentration of CFSE+ particles in EV samples be a more accurate way of measuring EV concentration?

Today, the most commonly used techniques for assessing the concentration of EV samples are NTA and the determination of total protein concentration. However, the concentration obtained by NTA...

16 May 2024 6,910 1 View

How distributed generation has impacted the distribution systems in terms of its protection?

It´s known that generation distributed especially from solar energy power plants has increased sharply in the last ten years into distribution systems around the cities. Although it brings many...

05 April 2024 5,040 0 View

What is the scientific basis for many amino acid-based product to say "Do not apply foliarly to plum trees as there is risk of phytotoxicity"?

I have found many products in the market stating this, but I have not found any published article that describes this phytotoxicity issue with Plum trees that have been sprayed with an amino...

26 March 2024 7,522 2 View

How to solve the Fermi's Golden Rule (numerically)?

I'm trying to solve the integral shown in the picture. I'm using python libraries to plot the integrand (numpy and matplotlib.pyplot), as well as scipy.integrate library to solve the...

13 March 2024 271 1 View

¿Como piensas que el trabajo social individual y familiar contribuye al bienestar emocional y social de las personas en situacion de vulnerabilidad?

Con este pregunta se pretende que los lectores reflexionen sobre el papel fundamental de los trabajadores sociales, busca explorar como la intervencion de los trabajadores sociales puede llegar a...

10 March 2024 7,207 3 View

How many poses are sufficient for reliable molecular docking ?

I am doing molecular docking of the molecules that I synthesize and I am wondering how many poses would be necessary. I am doing this in maestro with glide and in the beginning by default I put 10...

21 February 2024 8,917 1 View

Similar questions and discussions
How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Are air moisture harvesting technologies effective in combating desertification?

Air moisture harvesting Air water collection devices

06 August 2024 5,473 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close