Does anyone know how to define a time dependent material property in ANSYS workbench?

More Samanthi Indiketiya's questions See All

How to find the dissolved SiO2 content in a liquid solution?

In a solid(powder) sample, it can be done using XRD or any other characterization method. Could you please suggest a method to find the SiO2 amount dissolved in a liquid sample?

06 April 2022 343 0 View

What happens if we use hot distilled water to wash away excess acids or base?

In general, when adsorbent materials are chemically modified we use distilled water to wash away the excess chemicals (e.g. after acid/base modifications, to wash away excess acid/base and confirm...

21 January 2022 9,398 3 View

Does Chitosan leach organics when used as an adsorbent to remove pollutants?

Many research has been done on the use of Chitosan as an adsorbent material. When I was studying the material, I noticed that it was leaching organics when I did a leaching test. Are there any...

07 January 2022 2,969 5 View

What is the accpeted level of VIF range for the higher order model in smart PLS?

Hello Researchers, I'm testing the type II (reflective-formative) higher-order model using PLS-SEM. Is it acceptable for Inner VIF>5 (less than 10)? What are the methods we can use to...

03 October 2021 5,055 4 View

Survey on finding the Effectiveness of Online Teaching & Learning during Covid-19 Pandemic

The spread of COVID-19 has led to the closure of educational institutions all over the world. Such closure accelerated the development of the online learning environments within those institutions...

01 January 1970 3,110 48 View

SURVEY ON FINDING THE EFFECTIVENESS OF ONLINE TEACHING & LEARNING DURING COVID-19 PANDEMIC - Teachers/Lecturers’ Perspective

The spread of COVID-19 has led to the closure of educational institutions all over the world. Such closure accelerated the development of the online learning environments within those institutions...

01 January 1970 8,225 4 View

Why the coefficient of permeability of some clays is significantly slowing down with time in flexible wall triaxial permeability.

Hi, we are testing the coefficient of permeability of a remoulded clay sample using AS 1289.6.7.3, flexible wall triaxial method. However, after saturation and consolidation perculation stage was...

01 January 1970 2,470 5 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

How do soil microflora interact with plant roots and influence plant nutrition, health, and productivity?

06 August 2024 9,618 3 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Jean Collomb

Hi,

In Ansys APDL it's possible to create table with time dependency and then to affect this table to a material for example. Thus, I think it's possible on Ansys Workbench. If not, you can create the APDL code into Workbench.

Samanthi Indiketiya

Hi Jean, thank you very much for your answer. I will check on that.

Zhimin Sun

Hi Samanthi, I face the same problem right now. Have you solved your problem? :)