What are some good polymer to use for packaging a biological product ,which can be steril by gamma?

As different polymers with different characteristics are exist,I want to know What polymers can be used for packaging an orthobiologic product(bone allograft),which can have enough resistent to...

22 December 2020 8,196 5 View

How to model Rainfall on sandy Soil or Slope using Python?

I had done some research in the field of rainfall simulation on sandy slopes, I did some tests on Laboratory and I did some modeling via Plaxis's Plaxflow module, I wanted to know if there is any...

29 November 2020 1,154 2 View

Is there a Deep Learning baseline (preferably written in PyTorch) for predicting animal pose from scratch (not like DeepLabCut or DeepPoseKit)?

I am looking for a animal pose estimation code that predicts the pose of an animal given 100-200 annotated frames from scratch using deep learning on a frame-by-frame basis. Is there any such...

27 September 2020 8,957 3 View

How authentic is this conference, https://www.scientificresearchers.org/icbe-8?fbclid=IwAR2_kI2DGxq7Hlc-Be6gIZKrwgXvjqg2Q5FT2SmIo2yiQecWAcMDpl7GZS0?

Good day, I just to want whether the above conference is a fake or not Regards

17 September 2020 3,912 7 View

Zetapotential measurement in hydrobromide solution?

Dear All I prepare pDNA-poly l lysine (PLL) nanoparticels in nuclesse free water and measure their zetapotential in the same media without dilution. The PLL comes as hydrobromide salt ( so -ve Br...

08 May 2020 2,017 10 View

How to do scale break in stata?

In the attached forest plot, I need to extend the gap between 0 and 1. I also need to add scale break between 5 and 9. Unfortunately, I couldn't do this with graph editor (stata) . Does anyone...

01 August 2019 7,261 2 View

How might I calculate hazard ratio and 95%CI from median survival rate?

I need to calculate HR and 95% CI for median survival rate in two different groups. i.e., Group 1: median survival=x and CI:(a-b) Group 1: median survival=y and CI:(c-d) I appreciate your help

24 June 2019 1,191 3 View

Does copy right stay very longer time?

How long does the publisher of Sensors and Actuators B hold the copyright of a published paper if it is not open accessible?

03 January 2019 212 3 View

Formula for different types of rainfall pattern?

is there any formula that we can use them to see whether our simulator is working fine and our simulated rainfall like the original rainfalls/? thank you for your time

30 June 2018 8,904 5 View

How can I obtain thermal strain of piezoeletric in abaqus ?

I want to simulate effect of temperature on piezoelectric material in abaqus. But piezoelectric element dos not have degree of freedom for temperature. Does anyone have any suggestions?

26 December 2017 3,128 2 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

How climate change will influences human and animal behavioral change?

The role of climate change influencing the human behavior as well as economics interest

01 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View