How to prepare the IMU data for OpenSim?

Muhammad Fairuz Abdul Jalal @Muhammad-Fairuz-Abdul-Jalal

02 January 2024 1 9K Report

I am collecting data on the upper limb using IMU from the Cometa System.

I am having difficulties preparing my data to be used for OpenSim. The joint movement in OpenSim does not follow what it should. I really need help in understanding and solving this issue.

Lushank RajendraKumar Shambharkar

https://youtu.be/0Nx_bUmSRvs?si=tkJGwx0NAon0x1ha

See if this might be helpful to you. I am facing the scaling issues on OpenSim

Badges
Science topic

More Muhammad Fairuz Abdul Jalal's questions See All

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

How to calculate the annealing temperature of a primer pair?

I have to amplify a gene and my primers just reached. The Tm for Forward primer is 64.2, and that of reverse primer is 65.5. Can some one suggest how to get the best annealing temperature? Thanks...

01 March 2021 360 7 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

The reason that the culture of white fungi Contamination with green mold(Trichoderma), the culture autoclave at121 for 15 min. What is it?

Is the period to autoclave not enough? The inoculation in a hood and flame and UV and alcohol.

27 February 2021 9,356 3 View

How to include original NMR data in a manuscript?

hello. i am junior researcher. I received a comment from a reviewer that he could not find NMR data in my submitted paper. I had included the NMR graph with explanation and formula to calculate...

27 February 2021 734 4 View

Does different dilution factors affect negatively on NH3 reading ?

I have a sample of treated water sample & asked to obtain ammonia conc. in sample using a machine with 5-25 ppm detection range. However, upon testing with different dilution factors, all...

27 February 2021 8,483 3 View

Can anyone share his experience regards Smoothing in origin?

I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...

26 February 2021 8,183 3 View

How do I report influence outliers in a pearsons correlation?

Good morning, I am running a correlation on phantom pain levels and self esteem scores in lower limb amputees. initially the data was reported as not normally distributed with the pain scale...

01 February 2021 600 6 View

Is it possible to use someone else's MOCAP data?

In order to study bone fracture in patients with osteoporosis, I need patient's exact muscle forces magnitude, location and direction (as FEM boundry conditions), while it is difficult to get...

18 September 2020 6,804 3 View

Can muscle force obtained from EMG while walking be validated with force obtained from CMC in opensim?

Can force obtained from EMG be compared with force obtained from computed muscle control in opensim?

17 April 2020 938 1 View

Is it possible to convert thigh muscle from MRI scan into 3D image for analysis in ANSYS?

I need to convert human lower limb bone and muscle into 3-D image for doing analysis in ANSYS. I have seen many research has made on structural analysis of bone but i haven't seen any article on...

03 April 2019 7,424 1 View

Can anyone help in the selection of the appropriate motor for an upper limb exoskeleton?

My graduation project is about rehabilitation using upper limb exoskeleton i have been searching papers for previous work in this field and i found everyone of them used different type (DC...

01 February 2019 4,812 1 View

What are the preventive strategies on phantom limb pain?

I am looking for preventive strategies on phantom limb pain. Please provide link to publications.

11 December 2018 8,988 1 View

What is Articular branch ?

What does the articular branch means For Example : Anterior interossous nerves gives an articular branch to the elbow Many Thanks

08 September 2018 2,833 0 View

What are the best features for EEG imagery limb movement classification?

I am working in the area of classification of EEG upper limb movements. I am working on the dataset right now, for this I wanted to know the best features for the feature extraction.

08 September 2018 3,653 1 View

Is it possible to extend conference paper into journal paper?

Dear RG experts, I have an accepted paper entitled " Investigation of friction condition between human skins at lower limb stump with different textiles" in the International Conference on...

06 July 2018 9,189 48 View

How can we determine the sample size from an unknown population?

My research involves upper limb and lower limb driving disabled people in my country. So what would be a reasonable sample size in this case since I can not readily quantify how many disabled...

05 June 2018 5,591 1 View