When I simulate my specimen with XFEM method I have faced an increment error. But when I decrease displacement or decrease the element of mesh the error disappears. I don't want to decrease the element so what can I do?
Do you know what my result depended to mesh?
i am searching for new sensors that is used in cars for effective performance of motor. can you give me a book or paper or introduce me a site?
31 December 2014 4,162 4 View
I want to model a twisted blade in ansys and nonlinear dynamic analyses, but solid element is not match with beam element and they are very different result. Now I don't know I select which...
08 September 2014 8,990 4 View
As you can see, my English language is poor specially in writing. i want writing a paper. i writed that fully but i have so wrongs in writing. are there any software that help me? what can i do...
07 August 2014 6,582 3 View
whenisimulate my CT specimen in Abaquse with Elastic-Plastic propertic my plastic zone in crack tip is lower than experimentall. i obtaine true stress and true strain from tensile test with this...
06 July 2014 6,070 6 View
When I use the XFEM method in Abaqus to predict fracture of my materials, Abaqus gives good results about crack initiate and maximum load, but it can't predict crack grows. In Abaqus, after...
06 July 2014 4,145 19 View
When I want to simulate crack growth with Abaquse in ductile material with XFEM I use Mapex damage criteria. But to do this I require two parameters, the first is max principal stress and...
06 July 2014 1,936 3 View
I fit my data in MATLAB with a function and I can see the results and coefficients in the command window. I need this coefficient in order to continue with my codes, but I can't input this...
05 June 2014 887 10 View
I simulate crack grows for a specimen in abaqus and use XFEM method. When my crack initiates and grows a bit and before full break the specimen I faced this error: too many attempt for this increment.
02 March 2014 4,125 31 View
I want use the data of tensile test of a material to determine fracture toughness of a material. What information do I need? Is it possible?
01 February 2014 7,653 12 View
I want to fracture test RTPMMA. I use the elastic plastic method for determin-integral. Do you know how much I let the crack grow?
01 February 2014 376 0 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...
08 August 2024 4,831 4 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...
07 August 2024 1,937 1 View
The stability of the Solar System is a complex subject that blends the classical framework of Newtonian mechanics with the modern insights provided by General Relativity (GR). Understanding this...
07 August 2024 2,569 1 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View