What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

Are protein samples in SDS compatible with ELISA?

I have used an AllPrep DNA/RNA/Protein Mini Kit QIAGEN kit to extract RNA and protein from my samples. At the end of the protein purification, I resuspend my protein in 5% SDS. Will these samples...

28 February 2021 7,370 3 View

Special issue on PLS-SEM in Mathematics. Are you interested?

21 February 2021 5,601 3 View

How to calculate the TCID50 when the highest CPE is 50% or less?

I am doing TCID50 to measure progeny virus and some treatments protected the cells in a way that the highest CPE observed is 50% or less. How should I do the titre calculation in that case? Thank you!

16 February 2021 8,768 1 View

Which drug is better to modify blood pressure in awake monkey, if I provide it in the food or drink reward?

I need to modify the blood pressure in a monkey while is awake in the recording chamber, and I am planing on provide a drug for that in the food or water used for reward... any advise? Thank you

08 February 2021 9,900 1 View

Why stop the reaction in ice for the fluorescent probe FDA (fluorescein diacetate)?

Hi, In literature I noticed that who stains haemocytes with FDA for 30 min then stop the reaction in ice while this does not apply for 15 min incubation time (or maybe authors did not write this...

08 February 2021 3,366 3 View

How to make Fast Green FCF from powder?

Hi everyone We need Fast Green to electroporate plasmid into mice embryos, therefore we simply need it to see some color in the liquid we are electroporating so that electroporation is more...

07 February 2021 1,671 2 View

Why do high doses of humic substances inhibit the growth of corn roots? Is there a toxicity effect?

Length, volume, surface area and dry mass of corn roots treated with humic substances increased up to 13 liters per hectare and decreased with higher doses.

02 February 2021 2,190 4 View

Using a nucleosil c18 column, i get no negative peaks in real time and two negative peaks in post run.Software problem?

Simadzu, lc solutions

02 February 2021 1,969 2 View

Any ideas on fast and easy way to stain mucus on intact cell layer?

Dear RG community, We are looking for a fast and easy way to stain mucus on a cell layer that allows for macroscopic visualization of mucus distrubution. Our epithelium is grown in conventional...

31 January 2021 6,790 2 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein?

Hi In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein? I got this error in the add-ion stage: Fatal error "./ amber99sb-ildn-HHH.ff / force...

01 March 2021 8,747 4 View

How can you bring two structures together to create an adhesive bond in LAMMPS?

I have created an Ice 1h crystalline structure and an Aluminium substrate structure and equilibrated both at 250K. Now I need to bring them together in a way that an adhesive bond is created....

01 March 2021 3,325 2 View