Is there anyone using CELLINK BIO X for 3D skin bioprinting?

Is there anyone using CELLINK BIO X for 3D skin bioprinting? Can you provide advantage/disadvantages of this brand? Would you recommend this brand?

17 June 2018 5,489 3 View

How to conjugate carboxylic acid functionalized CdTe Qds with thiolated oligonucleotides?

04 October 2016 4,035 1 View

Is it a common practice that researchers use q. experimental and sequential explan. design in a single research ie, quan+qual then pre+post test ?

07 May 2016 4,474 6 View

How can I prevent paraffin-embedded rat brain tissue sections from falling/coming off slides in H&E staining?

06 January 2015 5,025 25 View

What is the optimum time required for rat brain fixation after trans-cardiac perfusion?

24 December 2014 5,269 8 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View

Interested to stain mice tissue with WGA 488 conjugate, anybody has a protocol to recommend?

Interested to stain mice brain tissue with WGA 488 conjugate, appreciate if anyone willing to offer me some guidance or suggestions! Thank you!

28 February 2021 3,951 2 View

How can I publish a manuscript in free or low cost journal with good H-Index?

Dear all I am going to publish my manuscript which is from my thesis in a good H-Index journal but I found them very expensive(I don't have financial support) based on the exchange currency of my...

28 February 2021 7,800 6 View

B-mercaptoethanol (BME) protocol?

Hi everybody, I have been running a multiplex IHC which allow me to stain the same tissue with different markers (Primary Ab + Secondary conjugated Ab) (AF487, AF555, AF647). Since I would like to...

27 February 2021 5,028 2 View

Why do my MCFs not form monolayer?

Hello, I am looking for some expertise on culturing MCF7s. I purchased them from ATCC and I have been following all media and culture conditions. Media is EMEM with 10% FBS and 10ug/mL of...

27 February 2021 3,904 2 View

Can impedance of antenna be less than 50 ohms?

I am simulating helix antenna in hfss, right now, giving excitation with 50 ohms port. When I see the results of Z parameter (real). It shows lower than 50 ohms. Do not understand, if it can be...

27 February 2021 4,218 7 View

Is there anyone who experienced with cytotoxic effect of Hoescht 33342 dye?

Is Hoechst toxic to cells? In general, it is known as non-toxic. I am working with dsRED MDA-MB-231 cell line. I applied it for my PDMS-based microfluidic platform, for this reason, I incubated...

26 February 2021 9,119 3 View

Why my agarose gel staining sometimes looks not homogenic but like gradient (see the figure)?

I am worried about this overexposure of the upper part of the gel in the picture. Is it possible that this is the result of too much concentration of ethidium bromide? Why is there such a big...

25 February 2021 8,140 3 View

What is the suitable range of Sulfur content and Viscosity of Heavy fluid Oil that used in Kiln?

What is the disadvantages of high sulfur content to the ceramic burning process? and what is the effect of outranged viscosity?

24 February 2021 8,219 2 View