02 April 2023 0 926 Report

I am skilled in phase equilibria modelling and looking for a postdoctoral position. I can do calculations on partial melting, devolatilization etc.

More Bin Wang's questions See All
Why does the MFDFA algorithm need to calculate the profile of the time series?

As described in the Multifractal detrended fluctuation analysis (MFDFA) algorithm, it at first calculates the profile of the time series, and then other steps are operated on the profile....

05 August 2024 9,366 2 View

Differences between deep seated landslides and slope destabilization?

Hi, Could someone explain the primary differences between deep-seated landslides and slope destabilization? In particular, definition and characteristics, mechanisms and triggering factors,...

02 August 2024 4,212 2 View

A question about arbuscular mycorrhizal???

How long it takes for arbuscular mycorrhiza to establish and produce benefits under experimental conditions？

25 July 2024 5,208 2 View

Is it possible to run the AIMD within a system using virtual crystal approximation (VCA)?

I want to study the thermal properties of a mixed system which is constructed by virtual crystal approximation in VASP. When I try to run the ab initio Molecular Dynamics of this system in VASP, I...

19 July 2024 6,569 3 View

If I want to invent my own hypothesis testing method, where should I get started ?

If I want to invent my own hypothesis testing method, where should I get started ?

15 July 2024 5,376 5 View

Recommendations for Rapid Publication Journals in Traffic and Transportation?

I am currently working on a research paper focused on the control of Connected and Autonomous Vehicles (CAVs) utilizing multi-agent reinforcement learning methods. At this stage, I am seeking a...

14 July 2024 2,620 2 View

I've earned 1 best paper award and 4 best oral presentation awards. What should I do next?

I've earned 1 best paper award and 4 best oral presentation awards. What should I do next to elevate my academic capabilities to the next level ?

14 July 2024 6,071 5 View

How to start writing an anti-virus software ?

I read several information security books. How do I start writing anti-virus softwares ？

13 July 2024 8,180 1 View

Are my cells contaminated with mycoplasma?

I suspect my cells are contaminated with mycoplasma. I fixed the cells with 4% PFA and stained them with DAPI. Below is the image I obtained. I don't observe the typical small, rounded DAPI foci...

11 July 2024 7,786 3 View

How to distinguish the DRX prior austenite grains (PAG) by EBSD of the martensite transformed from PAG （Ausforming）?

During the heavy warm rolling process, austenite undergoes dynamic recrystallization (either DDRX or CDRX), and then transforms into martensite upon quenching. Is there a way to distinguish from...

11 July 2024 7,602 1 View

Similar questions and discussions
How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Given the current level of natural phenomena cause by the climate change and environmental pollution, will the AI find the technological solutions?

AI-driven technologies offer previously unheard-of capabilities to process enormous volumes of data, extract insightful knowledge and improve predictive models, according to the UN’s World...

31 July 2024 9,733 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close