Which antibodies to use in the study on rabbits?

Can anti rabbit antibodies be used in a study where the study model is a rabbit? Does that make any sense? Only one producer also reacted to the rabbit's reactivity...

23 October 2019 2,909 3 View

Do you know Poisson's ratio of cotton, wool, Spectra 1000, Vectran HS LCP?

I may try with values 0.3-0.35 for my models in Abaqus but I prefer to utilize verified values.

29 February 2016 8,635 4 View

How do I model in Abaqus the Heat transfer from Human skin to objects (textiles)?

23 November 2014 296 3 View

How do I disassociate human epidermis prior to enzymatic treatment to get the most cells out?

I've tried different ways of cutting it into small pieces but no matter how much I cut, they still look quite big. I think this is a reason why I cannot get higher cell numbers in my single cell...

29 October 2014 7,308 1 View

Does anyone know if Legionella dumoffii replicate in THP-1 activated cells?

We tested growth of L.dumoffi in activated THP-1 cells after 72 h time of incubation and noted any presence of bacterial colonies on BCYE plates.

31 December 2013 1,029 2 View

Looking for Materials with high thermal expansion coefficient and high temperature resistance?

03 March 2021 8,272 1 View

What are the most reliable approaches to extract key continuous frames from a video, with complete automation?

I have an input video, of skin (from a microscope that means it is magnified such that blood capillaries are visible). The idea is to extract 15 sec of continuous frames from a video of 1 min,...

02 March 2021 2,735 2 View

What are anisotropic electrical and optical properties of a semiconductor due to?

In some materials, properties such as band gap, thermal conductivity differ along different crystallographic axes. What are the basics?

01 March 2021 1,923 3 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Why do a weight decrease for thermal degradation in nitrogen gas condition?

Hi all The question is related to TGA(Thermogravimetric analysis). Thermal degradation easily understood but why do samples weight decrease? altough just binding is broked, the weight of...

26 February 2021 1,100 5 View

Can thermal cycler machines be problematic during PCR?

Hi, my question is about the heating of thermal cycler machines and I hope some of you had experienced a similar thing previously. There are two thermal cycler machines in the lab(BioRad) and for...

26 February 2021 4,777 4 View

What is the best surface to culture cells isolated from a skin biopsy?

Hello, recently I am having some difficulties with maintaining the cell culture of primary cells isolated from a skin biopsy (normal and malignant). The coating of culture plates with Matrigel (a...

26 February 2021 6,151 2 View

How to increase solubility of Poly acrylic acid in Dioxane solvent?

I am working with Polyacrylic acid (100.000Da) and instead of water, I need to use another solvent (dioxane) to dissolve PAA. However, because of the high molecular weight, it's quite hard to...

25 February 2021 2,225 5 View

How can I verify my centrifugal fan design for electric motor cooling?

I have radial blade centrifugal fan design which will be mounted on exhaust side of electric traction motor. The fan will be mounted on same motor shaft inside the housing. How can I verify that...

23 February 2021 2,390 3 View