Difference between Langmuir surface area and BET surface area?

More Fa Najafi's questions See All

A question regarding Response factor in GC. what does area count mean?

i was reading about response factors in GC and i encountered the term area count, I was wondering if anyone can explain it to me, i have a general idea about the meaning but i'm not sure. does...

30 March 2020 7,854 1 View

Which software is best for estimating of pipeline corrosion rate?

I want to calculate Steel pipeline corrosion rate in different conditions, so Which software is best for estimating of pipeline corrosion rate?

03 March 2020 1,779 4 View

EEG connectivity calculation via HERMES toolbox ?

Hello everyone I am currently trying to calculate phase lock value for my EEG data with the help of the HERMES toolbox in Matlab. I have a total of 48 subjects with different channel location...

04 January 2020 5,220 1 View

How can one simulate agglomerated cork in ansys and which engineering model can provide the better results?

I'm going to simulate the structural response of a sandwich structure with agglomerated cork core under bending and compression loading. Is there any reliable information about the structural...

28 August 2019 2,843 2 View

Hi.I have an extruder for dewatering a two phase fluid. I want to setup slip condotion in wall boundary condition in Ansys Fluent. how can I do that?

in wall boundary dial box I should specify the shear stress in three direction (x,y,z). how can I measure this shear stress? please help me....

10 June 2019 7,550 1 View

What are the best polynomial approximation functions for analyzing free vibration and impact analysis of plates?

I want to do a free vibration analysis for a plate. In this research, I want to use the Ritz method. For Ritz-shape functions, which are the best polynomial functions that give the most accurate...

10 April 2019 2,612 5 View

Can I still publish a paper if there is something rather similar in a patent?

I've tested a variety of reagents for the synthesis of a compound and found one that has never been used before and yields a good product. after my experiments i did some research and came across...

04 September 2018 5,726 3 View

What does a higher (or lower) soil sorptivity indicate?

sorptivity is defined as the capacity of soil to absorb or desorb water by capillarity. but what does higher sorptivity mean? does it mean the part of infiltartion that depends on capillarity...

30 July 2018 4,467 4 View

A question about MALDI/TOF MS?

I am a Ph.D. student of microbiology in Iran. Actually, I have found a bacterial peptide that I want to identify that using MALDI TOF MS. I am looking for anyone with experience with MALDI TOF MS...

23 April 2018 9,654 5 View

Has anyone had problem with single cell whole genome amplification?

Hello, I am experiencing problem with single cell whole genome amplification from 10-12 cells only 3 or 4 amplifies and I have a smear on gel electrophoresis, Can anyone help me? Best Regards

12 February 2018 3,212 5 View

Gas sensor response and recovery time independant of flow rate and chamber volume?

I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...

26 February 2021 1,511 3 View

Physical-chemical formation of stalactites/stalagmites. what promotes the formation/growth of these structures?

I know, or think I do, the basic idea behind these natural structures, as from what I know they form due to water dripping from the top leaving a salt deposit behind. But started to wonder about...

22 February 2021 1,400 4 View

What are some underexplored theories and concepts in Activated Carbon as A Water Filter?

Hi, me and my team mates are currently planning to pursue the topic of Activated Carbon from Coconut as a Water Filter. And we would like to ask for your suggestions and knowledge on what specific...

21 February 2021 7,561 4 View

How can we study the adsorption efficiency of microgel at the oil-water interface?

I am studing the mircogel at oil-water interface. I want to know the adsorb amount of microgel at the oil water interface. How we can determine this amount?. I will highly appreciate your...

19 February 2021 2,787 1 View

NVT or NPT is preferable for gas adsorption simulation ?

Hi there, In order to perform molecule dynamic simulation on gas adsorption on substrate materials, NVT or NPT ensemble is preferable ? Thanks!

08 February 2021 173 1 View

How do you prepare a porous crosslinked Polyvinyl alcohol and Glutaraldehyde membrane or film?

I am trying to prepare a Polyvinyl alcohol membrane for carbondioxide adsorption

08 February 2021 7,493 3 View

Which is the most ecofriendly and effective activated agent for the preparation of activated carbon from sewage sludge?

I am going to prepare activated carbon from the waste activated sludge coming out of WWTP. Can you please help me in understanding, which chemical/physical activating agent will be most...

07 February 2021 9,507 5 View

I need help with adsorption kinetics. Basically non-linear plots of pseudo first, second order, avrami equation, elovich and intra particle diffusion?

The questions are too twisted to be explained here. I was hoping if someone who has published a paper can guide me for the same. Kindly contact me at [email protected]. I'd be grateful.

01 February 2021 6,886 2 View

What could be the possible reason for the drastic variation in Qmax value for same adsorbent onto two different cationic dyes itself?

The adsorption capacity of the rice husk biochar was varying drastically with two cationic dyes namely Basic Blue 41 and Basic Red 09? What could be the possible reason behind this?

30 January 2021 1,420 3 View

What is the mechanism or interaction between Fe3O4 magnetic nanoparticles and biochar?

Lately there are many studies on biochar incorporated/loaded/coated with Fe3O4 magnetic nanoparticles. But I havent found any paper that describes the interaction or bonding between the two. How...

20 January 2021 3,162 4 View

Marta Litynska

It depends on properties of adsorbent and adsorbate. Sometimes polylayer adsorption is not possible, for example, in case of chemosorption.

Jorge Efrén Silva Yumi

Which method you used for Langmuir area? I think, there are many difference

Badreddine Belhamdi

This can give you the answer