CPM assay with rotor gene Q?

01 January 2017 0 9K Report

Hi,

I'm using the rotor gene q for my CPM assay and in the setup of the analysis I have to adjust the ramping rate to be 2˚C/min but the only way to do this is to adjust (wait for -- seconds for each step afterwards) and I don't know if there's something like equation for example that I can use to know what is the right seconds that I can adjust to reach this ramp rate

Ex. For ramping rate 6˚C/min this option had been set to be 4 seconds for each step

Badges
Science topic

More Marwa Amer's questions See All

Can any one help me with data analysis of Dual luciferase experiment?

Hi I did an experiment for miRNA and targets but I have a problem in calculating the significance of the data can you help me which test should I have to use and how to caluclte the p value or z...

05 June 2016 6,272 4 View

Why there's no expression in western Blotting for transient expression?

I'm trying to express membrane protein gene in pACMV-tetO Flag taged one. I did a transient expression in HeK293 Gent- but when I did a western blotting (without purification) only the cell lysate...

05 June 2016 4,700 8 View

Problem in qPCR amplification plot?

I'm doing qPCR reaction using SYBEr green master mix Takara, When I did the reaction for the first time, I've got a good result but when I repeated it I got a strange plot that I can't explain. So...

31 December 2015 6,868 4 View

What's the optimum temperature for saving tissues in formalin or paraffin?

01 February 2015 8,052 4 View

How I can get RNAseq data-set for hepatocellular carcinoma?

I want to work on different RNAseq data-set for Hepatocellular Carcinoma preferably at different stages of the disease. I searched for these data-sets but I couldn't find them through the cancer...

04 May 2014 5,136 7 View

Is there any common antibiotic that can work on both puromycin and neuomycin resistant genes for the selection of transfected cells?

I want to transfect Huh7 with two different vectors one containing neomycin resistance gene and the other containing puromycing resistance gene. Does one of them affect the other or is there any...

10 November 2012 775 10 View

Any recommendations for starting micro array data analysis?

I'm beginning the analysis of my micro array experiment of me and I don't know which program is the most user friendly. What are the parameters for data analysis?

09 October 2012 2,342 15 View

Double Restriction digestion of a plasmid

I'm cutting miRNA expression vector with BamHI and NheI. I did the BamHI digestion by different conditions then cut with NheI. The problem is I have unexpected bands at some conditions and the...

08 September 2012 8,708 17 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

What is your perception on using visual analysis or quantitative approaches to evaluate data from single-case research designs (n of 1 trials)?

Results of single-case research designs (i.e., n-of-1 trials) are often evaluated by visually inspecting the time-series graph and computing quantitative indices. A question our research team is...

03 March 2021 687 1 View

How do I increase the yield of my PCR product?

Hello, We would like to increase the yield of our PCR product. We are running a series of PCR reactions that is targeting ~1.1kb sequence. We begin each reaction with ~400pg of template DNA...

02 March 2021 4,029 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View