Coupling FLUENT and RELAP5-3D?

09 September 2016 1 9K Report

Has anyone an experience in couple of CFD code FLUENT and system code RELAP5-3D? I know there is PVMEXEC program (from INL) but I cannot find link to download it. Any suggestions?

Zoubair Boulahia

Read this doc it may be useful for your topic. Good luck

Badges
Science topic

More Dmitry Fomichev's questions See All

How to analyze mesh sensitivity for huge CFD model?

Hi, everyone. Developing numerical models by CFD we should analyze mesh sensitivity, ie independence of results from the mesh size. This is simple for small models (up to approx. 100 on cells. But...

04 May 2018 8,042 1 View

A consideration on the heat transfer in liquid metal?

Dear researchers, Please, help me to find a pdf copy of paper - Aoki, S., 1963. A consideration on the heat transfer in liquid metal. Bull. Tokyo Inst.Technol. 54, 63–73. Thanks.

05 June 2017 9,706 3 View

Have someone got a human heart 3d model?

I'd like to conduct a test CFD (FSI) simulation of human heart. Thanks.

31 December 2016 2,650 5 View

Verification and validation (V&V) of CFD codes?

Do some can share any files on CFD V&V? Expecially I would like to get Fluent Verification Manual for Release 17. If you can download it from Ansys Customer Portal, please share it with me.

11 December 2016 3,485 0 View

How to simulate PEMFC by CFD (Fluent)?

Dear colleagues, I've just started to simulate PEMFC by Fluent 17.0, and I have some questions about it. So, first of all, Fluent has addon module for PEMFC modeling. I can choose [3] FC and...

05 June 2016 3,559 26 View

Has someone got the Prandtl turbulent correlation applied to the liquid metal?

Dear scientists, I'm looking for Prandtl turbulent correlations applied to liquid metal (expecially, lead). I would like to compare it with results of CFD simulation. It can be liquid metal flow...

01 February 2016 2,901 3 View

Consulting Services Market Analysis on CFD modelling

Please answer the following questions: 1. Are your company ready to provide consulting services for math simulation and CFD modelling? 2. Do your company need such service? 3. What industry are...

01 January 1970 7,733 1 View

Can't spin-orbit coupling(SOC) be included in optical properties calculation in CASTEP?

I am currently using CASTEP version 2020. When I want to run optical properties calculations with spin-orbit coupling(SOC), I encounter the following error in a pop-up window before the job gets...

02 August 2024 2,890 0 View

Problem with Two-phase simulation?

Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...

25 July 2024 2,309 5 View

How to introduce on fluent the optical loss of the wall due to the reflection of the plate towards the environment ?

"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...

13 July 2024 8,621 5 View

How to add a mass source term in the continuity equation?

Hi, I am trying to model laser cladding in Ansys FLUENT. There are two phase: one is base metal surrounded by an inert gas (shown in the image). I want to add a cladding layer of the same metal....

07 July 2024 1,182 8 View

Why i can't get access to isosurface in fluent?

hello everyone i get into fuent and i select the result icone then i try to create an isosurface but the button is gray so i can't choose it. what's the problem? any suggestion.

03 July 2024 5,418 4 View

How to solve the question of ansys fluent?

Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."

30 June 2024 7,894 1 View

How to converge PEMFC in Ansys Fluent?

I am simulating 1 cell of PEM with an area of 50 cm². The mesh has an orthogonality of 0.2 for the channels and bipoar plates (polyhedra) and a quality of 1 for the active zones (hexagonal). The...

26 June 2024 2,358 0 View

Can anybody recognize the virus on potato plants?

Infected potato plant was negative for PVY, PVX, PVM, PVS. What can it be?

19 June 2024 6,739 3 View

What is the exact mathematical formulae and the C++ code of EMMS drag model that is used and applied in ANSYS Fluent 2023?

EMMS - Energy Minimization Multi-Scale

18 June 2024 5,857 2 View

How to compile a udf in Fluent to import hourly weather data and update the boundary condition based on it ?

Hello all, I've compiled a udf which reads velocity data with corresponding time stamp from a .csv file using DEFINE_ON_DEMAND macro. Then, I use DEFINE_PROFILE to define an inlet velocity profile...

14 June 2024 6,480 0 View