Could you suggest me the numerical simulation model to explain the chromosphere heating and plasma Outfolws?

01 December 2022 0 2K Report

There are different model and theory to describe the increase the temperature of chromosphere and plasma speed. I would like to know about tested model which agree with observation.

More Ram Chandra Pageni's questions See All

Is there any way to quantify bacterial and fungal cells in their mixed culture?

I am working in fungal fermentation of soybean meal and there is bacterial growth in them at times. I am trying to quantify fungal cell counts and bacterial cells; but I haven't been able to do at...

07 August 2024 7,535 4 View

Is it fare for editors of reputed Journals to put on hold manuscripts more than six months without review updates, Are they harassing researchers?

It is being seen that Editors of some reputed Journals are putting on hold the manuscripts and not updating review states even passing more than six months from submission. Researchers are...

24 July 2024 8,596 2 View

Can I Use D-PBS for Preparing a 10% Sucrose Solution for Lentivirus Concentration?

Hello, I am a master's student currently conducting lentivirus transduction experiments in Jurkat cells. The virus is not effectively entering the Jurkat cells, so I am planning to use an...

21 July 2024 4,676 4 View

Unification of General Relativity and Quantum Mechanics is possible ?

How can anyone develop a theoretical framework that successfully unifies general relativity and quantum mechanics? how this new theory should accurately describe gravitational interactions at...

10 July 2024 5,040 8 View

The field of cosmology and general relativity is vast and intricate,mistakes in tensor calculations, which are fundamental in general relativity ?

The field of cosmology and general relativity is vast and intricate, with numerous potential areas for misconceptions and errors. Initial mistakes in tensor calculations are some common mistakes ?

27 June 2024 6,329 2 View

Sulphur test method for edible oil?

Hi everyone do you have any method for sulphur test in edible oil? as per lower cost, which instrument we can analyze sulphur in edible oil?

29 April 2024 9,789 0 View

How to write a research paper?

please tell the research paper writing steps from beginning to end.

24 April 2024 978 5 View

What can be the alternate buffer for TAPS (PH 8.5) in Post tagmentation Wash step in Cut & Tag experiment ?

I am performing Cut & Tag experiment. I was wondering if there is any alternative/replacement for TAPS pH 8.5 in single tube Tagmentation and pA-Tn5 release ( DNA purification) step of Cut and...

02 April 2024 4,214 0 View

All the research papers (4-5) of PHD are in one journal, what impact will it have for future job in academic career?

If after doing PhD, a research scholar has 4 to 5 papers published, and all are published in the same journal (SCIE), then what impact does it have on his future teaching, academic career, or...

30 March 2024 3,615 1 View

How much of primary antibody do you add on slides in immunohistochemistry(IHC) / Immunocytochemistry (ICC)?

Most of the Antibody company (having pr. Ab conc. range 0.2 mg/ml - 0.5mg/ml) websites suggests dilution around 1:200, but it seems not staining or faintly staining. What is the hand on experience...

28 March 2024 259 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

How much total RNA concentration to be extracted from sorted plasma cells from bone marrow of C57BL/6 mice for RT-PCR ?

i have sorted anti-NP specific plasma cells from bone marrow of C57BL/6 mice at certain times after immunization with variable counts and isolated total RNA using TRIZOL method for RT-PCR using...

05 August 2024 8,835 1 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View