Could you present more detailes about your CFD setting?

01 January 1970 1 9K Report

I have read your concise article even though could I request you more details about CFD set up in the simulation particularly about the velocity of wind profile regarding to building floor basis?

Md. Washim Akram

The attached article may help you.

https://www.sciencedirect.com/search?qs=more%20detailes%20about%20your%20CFD%20setting&show=25&sortBy=relevance

https://www.youtube.com/results?search_query=more+detailes+about+your+CFD+setting

http://www.google.com/search?sourceid=chrome&ie=UTF-8&q=more+detailes+about+your+CFD+setting

Chapter Practical Guidelines for CFD Simulation and Analysis

Badges
Science topic

More Hamed Majidian's questions See All

How the meshing of a complex structure such as shark skin reiblet in the large scale number could be achieved by Ansys either other CFD programs?

Griding of complex structure in enermous numbers like a huge scale plate is a hard eloborate and mostly impossible. How this task could be implemented in a 3D plate with 100 x 10 x 2 meters dimension.

04 May 2019 9,848 13 View

How can I set up a pulsate flow in ansys Fluent or CFX?

I am going to simulate a pulsate flow with negative and positive velocity around a blunt body in transient condition.

04 May 2018 8,903 0 View

How should I simulate the moving sphere in Ansys CFX or Fluent?

I am going to simulate a spherical blunt body moving in water along Z axis in a limited range of oscillation. I know I have to use transient condition with dynamic mesh but I need more details...

04 May 2018 6,540 13 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Can we distinguish the type of free fluid inside the pelvic and abdominal cavities whether blood or serous fluid using the ultrasound?

during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...

01 March 2021 7,476 4 View