Concrete Smeared Cracking

03 March 2015 0 9K Report

Does anyone know how to calculate the Concrete Smeared Cracking in Abaqus using numerical approach? Or does anyone has the journal which contain the equations to calculate the Failure Ratios, Shear Retention and Tension Stiffening? Thank you very much

Badges
Science topic

More Asdam Tambusay's questions See All

How to define stirrup or transverse bar using ECC material in ZEUS NL?

I am confused to model the section of rectangular column section in ZEUS NL using ECC material. In the section module there is no input for the stirrup, only for longitudinal reinforcement....

02 March 2016 2,902 0 View

Does anyone know how to model reinforced concrete structure using dynamic explicit in ABAQUS?

Hi Colleagues, I want to model the reinforced concrete slab-column connection subjected to displacement controlled reversal by using Dynamic Explicit step in ABAQUS. But, It seems like I have...

10 November 2015 9,416 0 View

Is there any publication that contains the complete modeling procedure of cyclic loading analysis by using ABAQUS (whether Explicit or Implicit)?

Dear Researchers. I am currently modeling the behavior of concrete structure under cyclic loading test by using ABAQUS. I am sort of confused regarding the proper modeling technique in order to...

09 October 2015 3,403 4 View

Is there any differences between nominal shear stress for conventional concrete and for engineered cementitious material?

I am evaluating the bahavior of slab-column connections under various gravity shear ratio. The involvement of nominal shear stress on concrete material (whether using regular concrete or...

07 August 2015 1,331 9 View

How do I model concrete that has the tendency of strain hardening behavior?

As known that Concrete Damage Plasticity (CDP) has been widely used for numerical modeling in ABAQUS due to its feasibility to model quasi-brittle material i.e. concrete. However, there are types...

04 May 2015 5,242 5 View

Can anyone advise where I can find some articles about "The Calculation of Tension and Compression Recovery in Abaqus"?

I am simulating the flat slab model under cyclic loading. I am using CDPM for the material properties of the concrete. In order to define the stiffness degradation in each cycle, tension and...

03 April 2015 5,018 4 View

How can I define or calculate the tension and compression recovery on damage parameters using Abaqus?

I am having problem to determine the precise value of tension and compression recovery in CDPM Damage Parameters. Does anyone know how to obtain the exact value?

03 April 2015 680 6 View

Does anyone know the proper simulation about how to model reinforced concrete joint structure due to cyclic loading in AbaqusCAE?

Hi All, I am trying to model the flat plate structure using nonlinear analysis in AbaqusCAE 3D solid finite element are used to simulate the concrete material and 3D truss element for the...

02 March 2015 2,534 2 View

Does anyone know how to model fiber reinforced concrete in Abaqus?

I am trying to simulate a reinforced concrete structural element in Abaqus by using PVA-ECC fiber. Due to its small dimension, what is the best way to add amount of fiber in Abaqus? I am confused...

02 March 2015 3,054 24 View

Does anyone know what is the best material plasiticity of concrete to modeling the quasi-static in Abaqus?

I am trying to modeling the slab-column connection under cyclic loading. Loads are given by using displacement controlled. I am following the procedure of geomtery model, boundary condition, and...

02 March 2015 1,759 2 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

What is the procedure to determine the permeability of concrete?

can anyone help me in this, it will help me with my research work

01 March 2021 834 3 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

How to assign different material properties to each element in Abaqus ?

Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...

01 March 2021 9,511 3 View

Apart from Nanosilica and CNT's what are the other nanomaterials readily available to use in concrete mixture?

Nanotechnology in concrete materials

01 March 2021 3,379 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

Concrete compressive strength databases?

I am looking for datasets similar to this one: http://archive.ics.uci.edu/ml/datasets/Concrete+Compressive+Strength I am looking for concretes with different types of aggregates (Recycled,...

27 February 2021 6,801 3 View