Comparison between the Hydrodistillation & SFE extracted essential oils

More Hicham Mechqoq's questions See All

Sililated organic extract GC-MS, Kovats index or Van den Dool and Kratz index ??

dear colleagues, I'm doing a GC-MS analysis of presilylated extracts with BSTFA (essentially polyphenols) and i want to determinate an Index to compare with adams book (2007), which index should I...

09 October 2019 4,144 2 View

How to Interpret ANOVA's results ?

Dear colleagues I have made two ways ANOVAs and post hoc tests, I have obtained the ANOVA's table (SCE, f & p values) with approximatively similar values but the entered responses were different,...

09 October 2019 2,204 8 View

Which reagent is better for lipids HPTLC revelation ?

Dear colleagues, I'm doing an HPTLC of several plant oils to compare their lipidic profiles, i have two protocoles the first one with sulfuric-vanillic acid, the second with phosphomolibdic acid....

08 September 2019 4,748 5 View

ABTS radical scavenging protocole modification ?

dear collegues, i would like to study the radical scavenging effect of some plant extracts against ABTS, and i would like to know if i can change the sodium persulfate with sodium sulfate and the...

06 July 2019 3,518 4 View

How can I interpret the GC-MS results obtained after sililation of an extract???

Dear collegues. I have analysed some extracts by GC-MS after sililation and i have obtained my report after comparing the results with the NIST database, Before doing more bibliographic...

02 March 2019 4,192 4 View

ABTS or DPPH: Which antioxydant assay is the best for an bioautography test on TLC?

Dear collegues, I'm doing an HP-TLC of some extracts and would like to do an antioxydant screening on plate (DPPH-TLC or ABTS-TLC) I would like to know wich one is the best and why ??

31 December 2018 9,829 4 View

Can the fluoresent colors of compounds on a TLC under 366nm be inerpreted ? if yes which compound correspond to which color ?

i'm doing TLCs and visualising my plates under 254nm & 366nm, I would like to know if it's possible to correlate the fluoresent colorations i obtain with families of secondary metabolites.

09 October 2018 8,121 6 View

Payed publications VS open acess ? do you think we will still have payed publications after 20 years ?

After the use of paper hack tools such as sci-hub the majority of journals prefer the open-access format where the authors pay the publication to be shared. Do you think we ll still have pay to...

01 January 1970 9,435 3 View

How to increase a model accuracy ?

dear community, my model is based feature extraction from non stationary signals using discrete Wavelet Transform and then using statistical features then machine learning classifiers in order to...

03 March 2021 6,994 5 View

What are the most reliable approaches to extract key continuous frames from a video, with complete automation?

I have an input video, of skin (from a microscope that means it is magnified such that blood capillaries are visible). The idea is to extract 15 sec of continuous frames from a video of 1 min,...

02 March 2021 2,735 2 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

How can extract ciprofloxacin hydrochloride disolve in water er to organic solvent such as dichloromethan or any other solvent?

I need a procedure to extract the ciprofloxacin hydrochloride from aqueous solution by using dichloromethane in detail,. I thank you very much.

01 March 2021 4,306 1 View

Can we distinguish the type of free fluid inside the pelvic and abdominal cavities whether blood or serous fluid using the ultrasound?

during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...

01 March 2021 7,476 4 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which bacteria are suitable for quorum sensing screening?

I want to find a quorum sensing inhibitor from plant extracts. Klebsiella pneumoniae, Moraxella catarrhalis, Staphylococcus aureus, and Streptococcus pneumoniae. I looked for these strains...

01 March 2021 7,675 3 View

How to perform statistical analysis of coefficients extracted from transform techniques?

I am studying the potential of DCT and FFT coefficients extracted from a signal to classify the different objects that emit the signal. I applied the Shapiro-Wilk to confirm that data was not...

01 March 2021 8,079 2 View

Hamza Belkhodja

SFE provides a rapid and quantitative method for extracting essential oils.

the hydrodistillation extracts were light yellow, while the SFE extracts were dark green indicating the extraction of chlorophyll along with the essential oils.

you can find more differences in the attached file

Samaneh Mahmoudvand

U study this article:

Article Comparison of hydrodistillation and supercritical fluid extr...

Nor Azah Mohamad Ali

SFE will mostly produce extracts rather than oils, but sometimes you may get oils with the right parameters. You may be able to increase the percentage of certain chemical compounds, higher yields with SFE compared to normal distillation.