Coating graphite flakes, electro or electroless plating?

Rajashekhara Shabadi @Rajashekhara_Shabadi

02 February 2014 1 5K Report

I have been looking for a method to uniformly coat Graphite particles with either nickel, Ti, or Ag. Has anyone some experience in that? Can somebody suggest the methods of coating graphite?

Graphite is in the form of flakes, some microns width and some nm thickness.

Prajna Deepthi

You can also coat with copper by electroless process. for this you need coppersulphate

Badges
Science topic

More Rajashekhara Shabadi's questions See All

What could cause thermal conductivity of copper friction stir processed samples to decrease with increasing temperature?

We observe that the conductivity of FSPed pure copper decreases by some 9-10% at 250C, while the composite of Copper with Yttria particles retain most of the thermal conducting ability with a mild...

10 November 2013 9,056 4 View

Adherance of Polyaniline coating over stainless steel?

Is the electropolymerisation of polyaniline coating over stainless steel (SS) via Cyclic voltammetry technique is really adherant? Else how to improve the adhesion of the coating, whether any...

01 March 2021 8,220 2 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

Is there a method of determining feed digestibility without the need to re-pellet the feed?

I am aiming to determine the ADC values of a commercial fish feed, but I do not have a steam pelleter or extruder available to me. Ideally, the pellets could be coated with some inert marker....

28 February 2021 7,967 3 View

How to immerse bricks in wax ( for coating ) ?

Do we immerse the bricks horizontally or vertically ? #bricks#waterproofingsurface#civil#engeenering#chemicalengineering#wax#parafinwax

28 February 2021 6,685 2 View

For gelatin coating for culturing HUVEC.Should the gelatin be made in sterile water or PBS? Do I need to autoclave the gelatin soln after making it ?

I want to use 0.1% gelatin. Should that be made in PBS or sterile water? Should I autoclave the gelatin soln after making it in water/PBS?

28 February 2021 274 2 View

Why is my platinum counter electrode getting dirty during electrodeposition?

I am conducting anodic electrodeposition of MnO2 onto a stainless steel substrate, using a platinum strip as a counter electrode. This is done galvanostatically, with the current held between 5...

27 February 2021 1,829 3 View

What pH condition required to coat APTES on silica coated Fe3O4?

It's a hydrolysis reaction, which may produce by either acid or base-catalyzed reaction. so can anybody help me with this, which condition is suitable for this reaction?

26 February 2021 1,760 8 View

What is the best surface to culture cells isolated from a skin biopsy?

Hello, recently I am having some difficulties with maintaining the cell culture of primary cells isolated from a skin biopsy (normal and malignant). The coating of culture plates with Matrigel (a...

26 February 2021 6,151 2 View

Unknown debris sheets observed in cell culture flasks?

Hi, We culture neural progenitor cells in T175 culture flasks coated with PLO-Laminin. We have successfully grown these cells with our protocol for months. Recently, we observed large sheets...

25 February 2021 3,443 4 View

How does charge on working electrode changes with rising potential?

During performing CV of a GCE or modified GCE, we rise the potential in the first half of the cycle and reduce it in reverse half. During the first half, what is the nature of charge on GCE or...

25 February 2021 7,994 3 View