is it possible to quantify the deformation based on the deformed cleavage planes in a sample of galena under a metallographic microscope????
Dear Khadra.
Refer you to this paper
https://www.sciencedirect.com/science/article/pii/0001616066900952
B.regards
Instead of checking only the mRNA level, I want to check the active protein level of MMP-1 in Liver tissue from mice. How can I do that?
03 March 2021 1,763 2 View
I want to analyses the proportion of swimming sperm of three species of fish in two salinities. To analyse the proportion of swimming sperm in a Generalized Linear Model, I would use a Binary...
03 March 2021 2,297 3 View
03 March 2021 8,272 1 View
Hi. Please tell me what guidelines should i need to follow for questionaries' type research work in India. It is not hospital based work, we are conduction basic institutional based qualitative...
03 March 2021 2,037 3 View
Hi, I implemented a code to gabor filter cifar10 data but the images after being filtered and stacked are not clear like the original images. I think the problem is in the way I am using the...
03 March 2021 6,317 1 View
i am try to classify the x-ray images. During classification , can i block unwanted images (except x-ray image).
03 March 2021 7,100 1 View
03 March 2021 5,360 2 View
The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...
03 March 2021 4,107 4 View
If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis
02 March 2021 7,670 3 View
02 March 2021 5,204 3 View
i have problem in preparation of liver tissue with bad cell organelles and how i can adjust osmolarity
03 March 2021 8,890 1 View
I am growing the cells on coverslips and transfecting the fluorescent tagged protein directly on them. Then i want to observe these cells under confocal microscope. Currently i am just using...
01 March 2021 6,142 3 View
Hi! Thank you for your time, attention, and support. I am currently using FEM solver Abaqus to perform a set of balloon inflation simulations, trying to understand the deformation shape, stress,...
14 February 2021 2,524 4 View
Hi guys, I have no experience and little knowledge on immunofluorescence and confocal microscopy. I tried to visualize the expression of FXR in my cells (THP-1 macrophages), yet I did not...
11 February 2021 562 6 View
I know that this is a very difficult question, as the areas of application can vary greatly. However, if you want to operate low as well as high resolution (from a few millimeters to nanometers),...
02 February 2021 4,985 4 View
hello i am trying to study the mechanical deformation due to the humidity on a 3d volume formed of 2 phases. my equation are dw/dt =grad(Dm*div(w)) and the mecanical is sigma=E*beta*nabla(w)....
27 January 2021 5,201 1 View
Hello all, I am just newly doing a simulation to test the deformation status of a magnetized rubber-like material, which is in-compressible, under a shifting magnetic field. Try to find the...
22 January 2021 7,427 2 View
17 January 2021 8,952 3 View
Dear colleagues, We have observed large fluctuations in laser power in our setup and traced them down to fluctuations in laser beam polarisation. Attached is a schematic of the relevant part of...
14 January 2021 7,505 4 View
Do you think the majority of developing, underdeveloped, and even the developed countries lack in capturing the finer elements of behavioral data generated at various interactive and reactive...
13 January 2021 3,241 2 View