Cisplatin degradation temperature?

20 October 2022 0 8K Report

Can anyone please suggest me the extent of temperature we can heat cisplatin. I am thinking of preparing a conjugate of cisplatin with a protein for which I wanted to know the reaction temperature to be set. The protein is stable in high temperature. Please help me with your valuable suggestions as soon as possible.

Badges
Science topic

Similar topics
Clinical Pharmacology
Dosing

More Bably Khatun's questions See All

How to plot colour map in origin 9 if I have x and y data sheet?

I have one x column and for that x I have 100 y columns as y1, y2, y3 and so on. How to plot colour map in origin?

22 February 2020 9,861 3 View

Among Oxygen and mixture of Oxygen and Argon by 1:1 , which is better for removing CVD grown graphene from Cu foil?

I have Cu foil both side covered with CVD grown graphene. I like to remove graphene from one side without affecting the other side. Now I am using 1:1 ratio of Oxygen and Argon. Is this condition...

03 February 2020 3,689 2 View

How to calculate cumulative drug release ?

I have attached the method as well as calculations for drug release but could not find appropriate results even after several repetitions. It was clearly visible that there must be a high...

11 October 2019 699 3 View

In Sigma Aldrich and Alfa Aesar different type of Nafion solution are available. Which can be used for thin film deposition on FTO?

I have some powder samples. For photoelectrochemical measurement (PEC) measurements, I want to prepare thin film of my samples on FTO. Can any one please help me which Nafion solution I will use...

22 July 2019 1,918 6 View

Can anyone say why hydroxypropylbeta cyclodextrin swells more in basic pH than i n acidic?

I have studied the swelling behaviour and drug release pattern from hydroxypropyl beta cyclodextrin where I have found that the swelling and release % was more in basic compared to acidic. It...

04 July 2019 315 2 View

Can anyone help me analyse the XRD pattern attached?

I have tried to change the structure from CUR to CP. I know XRD is not mandatory here but since I did I would like to analyze the result. A very simple explanation will also be highly appreciated....

26 April 2019 5,459 7 View

Why we use modified stern-volmer equation?

The modified stern-volmer equation involves the assumption that free and total drug concentration are equivalent. Recently, a slightly modified equation to overcome this simplification has been...

08 September 2018 1,884 0 View

Where one can get this modified stern-volmer equation?

log(F0-F/F)= log Kb + n log[D]t The above equation involves the statement that free and total drug concentrations are equivalent. To overcome this simplifying assumption and to get a more...

08 September 2018 7,605 0 View

How to fit a non-linear equation?

Hi everyone, [D]t={(F0-F/F)*(1/Kb)}^(1/n)+n*[P]t*(F0-F/F) where [D]t and [P]t gives total drug conc and total protein conc. we want to determine Kb and n. we have a series of data for y=(F0-F/F),...

08 September 2018 793 4 View

How to fit a non-linear equation?

Hi everyone, [D]t={(F0-F/F)*(1/Kb)}^(1/n)+n*[P]t*(F0-F/F) where [D]t and [P]t gives total drug conc and total protein conc. we want to determine Kb and n. we have a series of data for y=(F0-F/F),...

07 September 2018 873 3 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

How does an antibody have full intact antibody + half antibody?

Hello, I was just wondering how does a antibody have full intact antibody + half antibody? Is it because of the drug conjugation?

28 February 2021 1,577 1 View

Interested to stain mice tissue with WGA 488 conjugate, anybody has a protocol to recommend?

Interested to stain mice brain tissue with WGA 488 conjugate, appreciate if anyone willing to offer me some guidance or suggestions! Thank you!

28 February 2021 3,951 2 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

Anyone that can help with Maxquant TMT16plex which is missing?

Hi I am very new to proteomics analysis. I have got raw files from core facility running thermofisher TMT 16plex 4 hours. I cannot find on maxquant the option TMT16Plex there is only up to 11...

25 February 2021 1,675 3 View

Antibody anti-IgM Bovin conjugated Biotin ?

Hi everybody, Can anyone please suggest me an antibody anti-IgM Bovin conjugated Biotin ? I would like to use it in LUMINEX with a streptavidin conjugated phycoerythrin reporter. Thanks in...

25 February 2021 9,659 2 View

How to properly calculate the fluid solid heat transfer between polypropylene matrix and glass fiber in a porous medium?

I'm building a cfx model of thermoplastic pultrusion process on ansys and i have a doubt on how is the proper way to set this parameter in a porous medium

24 February 2021 1,915 1 View