How to plot colour map in origin 9 if I have x and y data sheet?

I have one x column and for that x I have 100 y columns as y1, y2, y3 and so on. How to plot colour map in origin?

22 February 2020 9,861 3 View

Among Oxygen and mixture of Oxygen and Argon by 1:1 , which is better for removing CVD grown graphene from Cu foil?

I have Cu foil both side covered with CVD grown graphene. I like to remove graphene from one side without affecting the other side. Now I am using 1:1 ratio of Oxygen and Argon. Is this condition...

03 February 2020 3,689 2 View

How to calculate cumulative drug release ?

I have attached the method as well as calculations for drug release but could not find appropriate results even after several repetitions. It was clearly visible that there must be a high...

11 October 2019 699 3 View

In Sigma Aldrich and Alfa Aesar different type of Nafion solution are available. Which can be used for thin film deposition on FTO?

I have some powder samples. For photoelectrochemical measurement (PEC) measurements, I want to prepare thin film of my samples on FTO. Can any one please help me which Nafion solution I will use...

22 July 2019 1,918 6 View

Can anyone say why hydroxypropylbeta cyclodextrin swells more in basic pH than i n acidic?

I have studied the swelling behaviour and drug release pattern from hydroxypropyl beta cyclodextrin where I have found that the swelling and release % was more in basic compared to acidic. It...

04 July 2019 315 2 View

Can anyone help me analyse the XRD pattern attached?

I have tried to change the structure from CUR to CP. I know XRD is not mandatory here but since I did I would like to analyze the result. A very simple explanation will also be highly appreciated....

26 April 2019 5,459 7 View

Why we use modified stern-volmer equation?

The modified stern-volmer equation involves the assumption that free and total drug concentration are equivalent. Recently, a slightly modified equation to overcome this simplification has been...

08 September 2018 1,884 0 View

Where one can get this modified stern-volmer equation?

log(F0-F/F)= log Kb + n log[D]t The above equation involves the statement that free and total drug concentrations are equivalent. To overcome this simplifying assumption and to get a more...

08 September 2018 7,605 0 View

How to fit a non-linear equation?

Hi everyone, [D]t={(F0-F/F)*(1/Kb)}^(1/n)+n*[P]t*(F0-F/F) where [D]t and [P]t gives total drug conc and total protein conc. we want to determine Kb and n. we have a series of data for y=(F0-F/F),...

08 September 2018 793 4 View

How to fit a non-linear equation?

Hi everyone, [D]t={(F0-F/F)*(1/Kb)}^(1/n)+n*[P]t*(F0-F/F) where [D]t and [P]t gives total drug conc and total protein conc. we want to determine Kb and n. we have a series of data for y=(F0-F/F),...

07 September 2018 873 3 View

How to analyze a particular region of my simulation box in GROMACS?

Hi, I am using GROMACS 5.1.4 to simulate water in contact with a surface. I am only interested to calculate some properties of water near the surface. Let's say at a distance of x nm from the...

03 March 2021 9,989 2 View

How to get onecolumn document from standard IEEE ACCESS LateX template?

I have prepared a manuscript in IEEE Latex template, but for some purpose, I need to prepare a word file as well (detailed format is not required). Compared to two column .tex file, one column...

02 March 2021 1,830 3 View

How can the modification of garden soil cause global warming?

Hello, I am working on a soil project and I found a primary research article that tests how the modification of agricultural soil can cause global warming, using a thermal collector, however I...

02 March 2021 7,161 3 View

Does anyone know how to plot my station to a section plot on Ocean Data View (ODV)?

I made a vertical section plot with WOA .nc file on ODV, and now I want to plot my stations (csv. file) in it. Does anyone know how to import my points to the section? They are two different...

01 March 2021 3,610 1 View

Does anyone know to clarify these changes?

01 March 2021 1,290 2 View

How can I convert .vesta file to a .cif file?

I've used the "export data" option in Vesta software to convert my unit cell into a cif file however when I use that cif in atomsk it shows error such as "can't read the position of atom 0". If I...

28 February 2021 4,966 3 View

How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials?

Hi, all! How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials? I have not find the choice for explicit element in Abaqus CAE. I am wondering whether it is possible...

25 February 2021 9,936 2 View

No title

25 February 2021 5,713 1 View

Anyone that can help with Maxquant TMT16plex which is missing?

Hi I am very new to proteomics analysis. I have got raw files from core facility running thermofisher TMT 16plex 4 hours. I cannot find on maxquant the option TMT16Plex there is only up to 11...

25 February 2021 1,675 3 View

How to search for crystal structure for material with atomic position labelled?

I am using the crystallographic open database and materials project to search for cif file but the exact structure is not mentioned or how can I deduce that the given structure and atomic position...

23 February 2021 6,723 2 View