Casting of H11 and H13 tool steels?

18 December 2019 1 5K Report

Are investment casting and squeeze casting the only techniques to cast tool steels, H11 and H13? If so, what is the reason?

Emil Hristov Yankov

The application of injection molding to H11 and H13 steels is to improve the structure and to unify the granular structure over the entire bar. The aim is to improve the technological and mechanical properties.

Badges
Science topic

More Peyman Samimi's questions See All

Comparing ATP Production Rates: Chloroplasts vs. Mitochondria in Photoautotrophic Cells?

In photoautotrophic cells under light conditions, what proportion of the total ATP is generated within the chloroplasts, as a rough estimate or within a lower and upper bound, and what proportion...

14 May 2024 6,492 2 View

"What subject should I choose for my doctoral thesis?

Hello, I am a PhD student in geography and rural planning. I am at the stage of choosing the topic of my thesis. I need your help all over the world to choose the topic.

07 May 2024 7,131 12 View

Choosing the subject of the doctoral thesis?

Hello, I am a PhD student in geography and rural planning. I am at the stage of choosing the topic of my thesis. I need your help all over the world to choose the topic.

07 May 2024 8,886 6 View

With what compounds can all the metal complexes formed with cyanide be precipitated? Is there a combination that precipitates all the metal complex?

A combination of copper sulfate and zinc sulfate can it ?

10 November 2023 4,027 1 View

What is the difference between the performance of lime and caustic soda in cyanide leaching operations?

Adding lime in the process, apart from the formation of calcium sulfate compound in the neutralization stage with sulfuric acid,if have the negative effect on the precipitation process of metals...

10 November 2023 5,776 2 View

When using grey literature in a scoping review, should multiple years of the same report be included?

I am conducting a scoping review and am wondering about a particular source of gray literature. An NGO produces a report that is relevant to my topic every two years. Two of them appeared in my...

26 September 2023 8,467 1 View

We use Navarro–Frenk–White (NFW) to calculate Dark Matter (DM) density. Can we use it for DM halo in any galaxy or is it used only for Milky Way (MW)?

Does NFW profile work for any galaxy?

08 September 2023 4,435 5 View

Considering the production of DM in another galaxy, how can I calculate "Dark Matter density" there (e.g., at special redshift)?

Calculating Dark Matter density in other galaxies rather than Milky Way

05 September 2023 1,468 0 View

Is it possible to calculate standard error for each mean from pooled standard error (SEM)?

If we have 4 treatments for a trait and a SEM (pooled SE) for these treatments' mean, how to calculate SE for mean of each treatment from SEM?

18 March 2023 3,587 3 View

How can we predict oocyte quality?

I suggest to read this new Review Article from me. Deeply, we categorized non-invasive engineering based approaches for predict or select oocyte by means of their quality. Oocyte quality...

13 December 2022 5,276 7 View

What is the reason for current dropping in OER , LSV curve?

I tried four trials of the same Copper Phosphides sample in Alkaline medium ( 0.5M KOH) with Hg/HgO reference electrode and Pt as counter electrode. I used 0.001 V/s scan rate for first three...

10 August 2024 3,629 1 View

What may be the reasons for failures of Tube toi Tube Sheet Joints in Boiler Drum ?

We have observed that tube to tube sheet joint leaked in our boiler and needs to overcome same by knowing the root cause.

08 August 2024 3,161 0 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

What is the problem with these tissue culture plants?

All plants are green but some of these plants becomes yellow. I did not found any reason. Please help me to find out the real problem.

01 August 2024 589 4 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?

25 July 2024 9,408 0 View

Reason for discontinuities in my Band structure?

Hey All! I am wondering what might be wrong with my band structure. I did the calculations using VASP and plotted the results using Origin. Although I have tried changing various input...

25 July 2024 2,920 11 View

How to saturate steel samples with hydrogen?

I have tried to saturate ferritic steel with hydrogen using the electrolytic method and H2SO4. However, the effect was very poor even after 3 days of "saturation". Can anybody help in choosing a...

24 July 2024 4,393 2 View