Can you use PLS-SEM in MASEM (Meta Analytic Structural Equation Model) or Two-Stage SEM?

Anak Agung Bagus Wirayuda @Anak-Agung-Bagus-Wirayuda

09 December 2021 0 3K Report

For undergoing MASEM or TSSEM, can we use PLS-SEM instead of the traditional SEM (CB-SEM)?

Badges
Science method

More Anak Agung Bagus Wirayuda's questions See All

How to do the Omnibus Test of Group Differences in practical way?

I am doing a comparison of multiple groups (more than 3) as a result of previous PLS SEM analysis. I have not yet found a clear paper or reading to technically do OTG (Omnibus Test of Group...

28 February 2024 2,631 0 View

Is testing MICOM (measurement invariance of composites) a must for PLS MGA?

I have data from population based observation (not questionnaires but yearly observation from secondary database) and I already have a common model for each populations (6 groups, each has the...

28 February 2024 7,434 1 View

What are common mistakes in writing qualitative studies?

What are common mistakes in writing qualitative studies? What are the characteristics? How to handle it?

17 November 2023 9,225 3 View

Are conferences held by ResearchFora authentic? anybody have any prior experience with conferences hold by them?

I am looking for a public health research conference around the middle east

07 June 2023 4,012 1 View

Is there an R package for FIMIX PLS?

I am looking for one but I could not get an info. I only found SmartPLS for such a tool, but I am looking for a free alternative.

21 May 2023 4,937 4 View

How can we write an interpretation of normal vs non normal data after conducting comparison statistical testing?

Dear seniors, We have two independent groups with normal and non-normal data distribution. For the normally distributed data, we present the data in the form of mean and its standard deviation...

05 March 2023 3,050 10 View

Is the article journal still considered as an international collaboration if there are 3 authors, and 2 of them from the same country?

As an example, if an article journal has three or four authors, two of them is from the same country, it should be considered as international collaboration or will consider as both of local and...

13 January 2023 1,702 4 View

Is it possible to build a GMM model with the number of observation (n) lower than number of years (t)?

I am currently trying to understand a possible dynamic panel model with the years of observation (t) higher than the number of unit of observation (n). The particular dataset contain 6 different...

09 December 2022 8,501 3 View

Is it possible to build a MIMIC Model in SmartPLS (PLS-SEM)?

So far, I knew that we can modify a construct with either formative or reflective indicators in SmartPLS. Is there anyone doing a MIMIC Model in SmartPLS (PLS-SEM)?

25 November 2022 318 3 View

Is it possible to conduct MASEM or Meta SEM based on PLS SEM approach, e.g., using SmartPLS and such?

I am about to conduct a study using Meta Analysis Structural Equation Model or MASEM/MetaSEM. I stumbled upon several discussions online stating that we cannot use PLS-SEM approach as it use...

06 June 2022 5,893 0 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 718 0 View

1. If I can quantize the atom using this hyperbolic spiral and classical physics, could nature do the same?

If we map as a continuous motion an ionising electron (beginning its journey at n=1) in an H atom, a specific hyperbolic spiral appears (see animation). When we solve this spiral formula, we find...

07 August 2024 5,342 2 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Weak DAPI staining after immunohistochemistry - how to improve?

After immunohistochemistry of previously fixed in PFA and EtOH and then frozen 20 μm sections of zebrafish brain, DAPI staining is very weak (right) compared to the same sections stained without...

05 August 2024 9,637 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 453 3 View