Can you suggest a detailed time domain solution of acceleration of carbody in rail vehicle problem?

Rakesh Chandmal Sharma @Rakesh-Sharma-81

11 March 2015 0 8K Report

Anyone who can provide detailed time domain solution of acceleration of carbody in rail vehicle problem?

More Rakesh Chandmal Sharma's questions See All

Which type of compound does lamda max of 218 indicate in a uv-vis spectrum of a partially purified compound through column and TLC?

A crude extract of fungal culture using EtOH was subjected to column and TLC and partially purified compound was obtained. UV vis spectrum of the compound/s has max absorbance at 218nm. The...

11 August 2024 9,801 2 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

Reason for discontinuities in my Band structure?

Hey All! I am wondering what might be wrong with my band structure. I did the calculations using VASP and plotted the results using Origin. Although I have tried changing various input...

25 July 2024 2,920 11 View

If my gene of interest has high GC content can it be problematic in sequencing? What kind of error is expected with GC rich gene sequences??

Gene sequencing related trouble shooting

25 July 2024 4,149 2 View

How to dispose off lipids waste?

I am looking for a lipid waste disposal method, keeping in mind the environmental, health and safety aspect of lipid waste. Could someone please provide guidelines or the lowest acceptable...

25 July 2024 637 5 View

What publications should I target as a psychology masters student in the UK?

I am writing a paper as a part of my course. I am new in London and was wondering that what publications should look upto?

21 July 2024 3,538 1 View

How effective has the United Nations been in addressing the conflict and its consequences?

After World War, we have seen the formation of the United Nations. The sovereign body for peacekeeping but with regards to the Russia-Ukraine war it is visible that the UN seems to be ineffective...

18 July 2024 4,674 4 View

What are the main obstacles to achieving a ceasefire or peace agreement between Russia and Ukraine?

It has been a quite long time since the Russia and Ukraine war has been going on and if we see the context of Geopolitics and International Relations we don't see a mediation between the two...

18 July 2024 6,737 4 View

How to decide whether the refinement is correct or not, based on Rwp and Rexp factors by Fullprof?

One of the papers I read by Toby, where (title of the paper was "R factors in Rietveld analysis: How good is good enough?"), he tells us that to get good chi square value, you must have low Rwp,...

17 July 2024 9,668 4 View

How to draw photon-magnon coupling color plot in origin?

Please help me in plotting the photon-magnon coupling plot as shown below

14 July 2024 1,632 1 View

Could you recommend some articles on Urban Transportation System optimization and Innovation?

13 August 2024 2,595 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View