Can you pronounce how to demonstrate the IDs corresponding to zones and gridpoints in FLAC3D in the working screen?

More Navid Yeganeh's questions See All

Hi, plaese guide anyone, how can we find the work function from XPS valance band potential?

Answer need on urgent base please.

16 January 2024 5,350 5 View

IAST selectivity and heat of adsorption?

Dear all, I have worked on the gas uptake with MOFs and now I need to calculate IAST selectivity and HOA. I've used python code which is published in some papers but it did not work for me. I...

25 December 2023 5,090 0 View

Can anyone help me with Sciex Q-TOF? What are Gas 1 and Gas 2, and also what is curtain gas?

I'm trying to switch a method established on Agilent Q-TOF to Sciex.

16 August 2023 2,565 2 View

Which kind of body fluid is applicable to measure MicroRNAs ? , AND What are challenges to detect MicroRNAs in body fluid samples?

To measure and detect MicroRNAs, researchers face many challenges, Some of them are: 1- Small size 2- Similarity in sequence in the same family 3- A tiny amount in the sample

19 June 2023 6,034 3 View

What to do for smooth peeling off of semi refined carrageen film from plastic petridish?

I have prepared thin films from semi refined carrageenan with hydrophilic cross linkers. But smooth peel off has been the issue for a long time.

06 June 2023 6,014 2 View

Fatigue and determination of life in the metal support structure of pressure vessels?

I am conducting an earthquake-induced fatigue study on the metal supports of the pressure vessels, which is responsible for the stability of the structure.

11 May 2023 4,649 2 View

Fatigue life calculation in pressure vessels using the Paris equation?

At the junction of the metal supports of the pressure tank, a crack has been observed that grows due to the earthquake. How is the fatigue life of the structure confirmed against the lateral force...

14 April 2023 1,296 2 View

fatigue life of the pressure vessel?

determining the fatigue life of metal bases of pressure vessels

14 April 2023 9,456 1 View

What is the relationship between Markstein number and Markstein length?

I am working on the effect of Markstein number and Markstein length definition in the internal combustion engines. Since mathematically they have a direct relationship, both should have similar...

04 April 2023 7,756 3 View

Hello I need three questionnaires in my research. If you have them, please send them. Details are mentioned below?

1.Learning satisfaction scale WAN(2014) 2.The perseverance in motor tasks questionnaire Zhou (1991) 3.Intrinsic motivation scale Lin et al. (2020)

19 February 2023 999 0 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

What precautions should be taken while handling S. aureus enterotoxin Type B in the lab?

I would like to understand potential safety concerns while handling SEB in the lab. Especially while working in animal house facility. Would like to know precautions for handling. Sigma MSDS...

07 August 2024 6,034 3 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

How to understand this crystallographic phenomenon of low temperature crystals in zeolite?

During low-temperature testing, new diffraction peaks that appear could be indicative of several phenomena. In one of our tests, we observed notable new peaks around 40° and 45° in a specific...

06 August 2024 726 3 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Navid Yeganeh

Thanks. Yet, let me shed light on my question via the figure below:

Hossein Khaleghi

Dear Navid,

FLAC 3D version 5 doesn't have this ability. Instead you can see the zones and gridpoints information by putting your mouse pointer on them and looking at "Information" window in "Control Panel" pane.