i am using 45nm technology to design LC network, i want to know the characteristics of 3-port inductor available in the 45nm technology such as quality factor, inductance, self resonating frequency, total impedance etc.
I designed simple LC oscillator using LC components available in pdk, but I am getting DRC and LVS errors with respect to inductor. In schematic the inductor have 3 terminals but in layout it has...
14 February 2024 1,251 2 View
i designed an simple oscillator circuit using MOSCAP but when i tried to do layout i am getting latch up errors , i am also using on chip inductor that is also showing error concerning the metal...
05 February 2024 7,422 0 View
I want to extract the electrical properties of MOSCAP in cadence virtuoso but I don't know the exact method how to measure resistance and capacitance and other properties of MOSCAP
05 December 2023 4,667 0 View
i am trying to design oscillator using onchip inductor available in 45nm technology in Cadence virtuoso but i am not able to get sustain oscillation due to damping. can anyone tell me how to...
23 July 2023 1,220 1 View
how to design cross coupled oscillator with low power consumption and wit oscillating frequency equal to 100MHz, how to choose RLC values in the tank circuit. is it require to add parallel...
23 July 2023 7,861 0 View
Active inductor are replacement for spiral inductors for their flexibility in terms of tuning inductance , frequency tuning and occupies less area. to design inductor for oscillator what are the...
23 July 2023 6,511 0 View
i am using cadence virtuoso tool 45nm technology for designing LC oscillators with 100MHz oscillating frequency, i wanted to do layout for my design but if I take LC components from analoglib , i...
20 July 2023 1,767 1 View
the main part of LC oscillators is its tank circuit, so i tried to analyze tank circuit seperatly by designing it in cadence virtuoso in 45nm technology. i used onchip LC components (available in...
20 July 2023 4,296 0 View
in adiabatic logic , the circuit is powered by trapezoidal wave but most of the literature mentioned that cross coupled oscillator as Asynchronous power clock generator which is sinusoidal in nature.
20 July 2023 6,243 1 View
i wanted to design ALU using Adiabatic logic , i have resources and when i implemented some basic adiabatic logic like ECRL and PFAL, i observed that , the power consumption depends more on the...
20 July 2023 3,925 0 View
Circuit Diagram: https://components101.com/articles/boost-converter-basics-working-design Good day Fellow Electrical/Electronic Engineers I am having a conceptual challenge here when deriving...
06 May 2024 3,289 2 View
I want to know how peak and rms current of diodes and capacitors are calculated in terms of output current? if you know good reference with details, please share here or tell me.
04 May 2024 6,277 1 View
what is open-circuit stepped-impedance resonators (OCSIRs)? why it is used in antenna design?
26 April 2024 7,583 1 View
A slot is made in the common wall between the two resonators. The parameter analysis was done on the slot‘s length , width and its offset from centre to evaluate its effect on the inter resonator...
10 March 2024 5,112 2 View
hi, I need a practical calculation and design for designing passive harmonic filter inductors. and the information about core sizing and considerations for 3-phase system.
09 February 2024 1,913 1 View
A boost PWM converter has the following data: VI = 125 to 350 V, VO = 380 V, PO = 6.8 to 68 W, and fs = 50 kHz. Compute the voltage and current stresses of the transistor and the diode. The...
02 February 2024 5,785 1 View
Generally unstable resonators have low M2 factor but still I do not know why and I have not a physical reasons behind this. We have some profile patterns in unstable resonator like doughnut shape...
11 December 2023 5,311 7 View
I want to measure LC resonator's voltage Wirelessly
19 November 2023 4,077 3 View