I am using ICP OES to quantify copper concentration in Samples.
liquid Argon is recommended for ICP-OES because it's high purity and provide a continuous argon feed
Also you can use high purity gaseous Argon ( 99.999 %) but you need a sires of argon cylinders
I use high purity Argon from cylinders.
economically high purity liquid argon is preferred
I am doing a acid and a chiral amino alcohol reaction using DCC and HOBT in DCM or THF? Can anyone suggest me how to remove DCU and HOBT from a reaction mixture??
28 February 2021 2,153 1 View
I am working in the area of Handwriting recognition for Bangla. As there are many DL architecture, I am confused which one to select.
15 February 2021 4,996 1 View
I am trying to import an Abaqus .inp file to Ansys but it does not import the whole assembly but only imports a single part. How to solve this.
17 January 2021 5,450 3 View
Since Abaqus CFD is no longer available in newer versions what are other available codes for Fluid-Structure Interaction Simulation
11 January 2021 2,012 3 View
I am studying about Impact load resistance property of Polyurea (Elastomer). With respect to this, I need to conduct tests on this material to evaluate its material model behavior as a...
29 December 2020 2,969 1 View
26 December 2020 4,280 5 View
I a writing a review article on cancer work through Mathematical modeling. If anyone interested in this work, kindly let me know
13 December 2020 7,585 10 View
I am writing my master thesis to simulate Energy Hatvest of OPVs in A year. Any advice on the same would be helpful.
03 December 2020 8,915 1 View
We are carrying out trial in the glasshouse where we are comparing the infiltration rate in sodic soil in two different treatments Polyacrylamide vs organic matter ( lucerne pellet). within 27...
25 November 2020 8,787 3 View
I am trying to create a voltage heat map of a distribution network in Matlab/Python. I have the values of bus voltage magnitude and angle but cannot plot them in a heat map. The objective is to...
02 November 2020 3,561 6 View
If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis
02 March 2021 7,670 3 View
I took measurements of different concentrations of 15 nm and 5 nm Au nano particle solutions. I'm trying to determine which concentration I measured gives the best reading overall. I also...
02 March 2021 7,626 1 View
I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...
01 March 2021 6,450 5 View
I am currently trying to stain for PI3KBeta in MDA-MB-231 cells. My current issue is that 1) beta stains all over the cell and 2) there is an increase in signal at the edge of the cell and this...
24 February 2021 8,582 1 View
Hello everyone, I'm looking for a way to delaminate copper current collector of water-based anodes in Li-ion batteries without damaging the graphite film. I tried different materials such as HNO3...
24 February 2021 3,785 3 View
To do liquid biopsy and look for specific gene expressions there are so many published papers. Thera are different protocols and procedures used to isolate circulating cell free RNA or mRNA from...
23 February 2021 7,326 5 View
I need to clean the hydrocarbon contamination on the carbon substrate of TEM grid. However, I heard that substrate could be broken by the powerful plasma. My substrate is pure carbon, with ~3nm,...
23 February 2021 3,262 5 View
20 February 2021 8,202 6 View
17 February 2021 4,217 3 View
I have been reading various articles and most state that treatment with CaCl2 produces higher efficiency of transformation than MgCl2. Can anyone explain why Ca2+ is better than Mg2+ at...
16 February 2021 8,519 5 View