Can we reuse electrolyte during ORR and OER electroclatalytic measurements?

More Ritambhara Gond's questions See All

Why is the hydrothermally prepared MoS2 nanoflower not adhering properly to the SiO2 substrate and not making proper contact with the electrode?

I have prepared MoS2 using a hydrothermal approach and then dropcasted it onto a SiO2 substrate. However, it is not adhering to the electrode and does not make proper contact, resulting in no...

02 April 2024 6,151 0 View

Why material (MoS2, ZnO or CuO ) dropcated on electrode is not conducting?

I am drop-casting MoS2, ZnO or CuO on an aluminum IDE electrode with a 20 um finger gap, but no conductivity exists. When I tested each aluminum pad of electrode separately with a multimeter, it...

05 March 2023 8,368 7 View

What is the optimum time (in ns) to do MD simulation for drug design ?

In my recent discussion with my colleague, he said that the 20 ns are good enough to do MD simulation, in another day, someone told me that either 30ns-50ns are needed to determine the complex...

07 January 2023 7,046 4 View

Hello everyone, I would like to ask something. Is there a suitable approach for screening compounds capable of binding to a protein?

I have run my MD simulation and I want to calculate the energy between my 2 chains, but i don’t know how to execute the ndx file? Thank you

29 November 2022 418 0 View

Can anyone help me with my MM-PBSA calculation?

I have run my MD simulation and i want to calculate the energy between my 2 chains, but i don’t know how to execute the ndx file? Thank you

29 November 2022 3,337 1 View

Hello everyone, I would like to ask something. Is there a suitable approach for screening compounds capable of binding to a protein?

Hello everyone, I would like to ask something. Is there a suitable approach for screening compounds capable of binding to a protein? We only know the amino acid sequence of the protein (without 3D...

29 November 2022 1,579 0 View

Hi all. Anyone knows what is the importance of hydrogen and hydrophobic interaction in docking?

I found that hydrophobic comprised of many types such as pi-sigma interaction, alkyl interaction etc. What are the differences between them? Can someone enlighten me? I am still new in this field....

26 September 2022 5,679 1 View

How to calculate the binding inhibition constant (kb) from the binding energy?

the molecular Docking simulation does not generate an IC50 value, it gives calculated inhibition constant (Ki) values! Unless you know a method and equation to make this conversion, you cannot...

23 July 2022 1,533 2 View

Why IC50 values are not compatible with docking values?

I did docking so I have delta G values for the top ranking ligands, i computed Ki using Ki = EXP(-delta G/RT). My question: Is there a way to calculate IC50 from this? I read somewhere we can...

23 July 2022 6,158 3 View

How to determine grid box coordinates? Any specific reason for the unfavorable Bump?

Any specific reason for the unfavorable Bump. What is an Unfavorable Bump?

23 July 2022 1,163 0 View

How to confirm the site-directed mutagenesis result without performing NGS?

I'm cloning a fragment of 3200 nts into plasmid. The cloning was successful, however, 02 amino acids were mutated. Now I want to fix these 02 aa by site-directed mutagenesis technique using...

08 August 2024 4,645 2 View

Self-Organizing Superorganisms—as envisaged by Nenad Sestan (2018)?

The rate of glucose consumption by the neocortex is reduced by over 80% during anesthesia (Sibson et al. 1998), which disables the synapses (Richards 2002) that are inundated by glial tissue (Engl...

08 August 2024 3,118 0 View

Aspen Plus Simulation?

Greetings When one is to perform Simulation or modelling of Pyrolysis of Biomass Waste materials using Aspen Plus software, and one has both the macromolecules breakdown (Cellulose, Lignin and...

06 August 2024 5,023 1 View

The Bigger You Are, the Harder You Fall (some lessons from Dinosaurs)?

Evolutionary fitness is based on an organism’s ability to adapt rapidly to changing environmental circumstances. Large-bodied mammals have been equipped with large brains (and hence a high...

06 August 2024 4,849 2 View

Are air moisture harvesting technologies effective in combating desertification?

Air moisture harvesting Air water collection devices

06 August 2024 5,473 2 View

RNA later for the preservation of RNA in fecal samples at room temperature for one day (37°C)?

I am planning to collect human fecal samples for metatranscriptomic analysis using MGI. These samples are from indigenous people living in a region with high temperatures. I will have access to a...

06 August 2024 1,367 3 View

Measuring the Intelligence of a Species?

Larger brains, which typically contain more neurons, store and transfer more information (Tehovnik and Chen 2015), but the precise relationship between number of neurons and information has yet to...

05 August 2024 1,238 2 View

If we are using snowball sampling technique, how do we justify the true representativeness of the sample statistically? is there any statistical test?

Are there any statistical methods to justify your sampling technique using SPSS or AMOS?

05 August 2024 9,153 4 View

Why my colony PCR results of my recombinant bacterial not showing any results?

I am performing ligation of the plasmid and a target gene. The steps I have taken are: 1. Double digestion of the plasmid and target gene 2. Ligation of the plasmid with the target gene 3....

05 August 2024 2,570 3 View

The Curse of Evolution and Complexity?

Brain and body mass together are positively correlated with lifespan (Hofman 1993). The duration of neural development is one of the best predictors of brain size, and conception is the best...

05 August 2024 6,247 3 View

Krishnakanth Sada

May be that's not good idea because during the experiment some active material may mix/peel off from the electrode. That may contaminate or interfere with new material.

Ritambhara Gond

Yeah I know sample peeling is possible but suppose if it is not there actually what measurements I am taking it just finishes in 2 Hr (30 min saturation, CV and LSV) so after that interval I want to replace my sample with different component.

No peeling off have happened now?