Hello everybody, Can anyone tell me how we can mesure the residuall stress in welded joint of pipelines?

I want to model the residual stress in welded joint in pipelines structures, can you please give me some models? thans Best regards

09 October 2016 3,011 0 View

Can any one tell me how and where i can find a physic and chemical parameters of soil?

01 February 2016 1,550 2 View

Hello, Can someone explain to me what's the strick-slip in soil and its influence on buried pipeline?

10 November 2015 4,192 2 View

How can I model a pipeline underground?

I want to simulate the the result of pipe-sol contact in presence of corrosion, so how can i modelate the contact pipe-sol in ansys software. thank you

08 September 2015 3,189 3 View

How we can modulate the soil caracteristique in Ansys code?

I want to modelate pipe-soil interraction?

04 May 2015 6,739 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

What is the most suitable server for predicting protein structures in bacteria?

I have used the i-Tasser several times, however it has been unavailable for several days. I tried the swiss-model, but the output was not very pleasant due to the model used. Is there any other...

28 February 2021 4,521 3 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View