Can we design surface texture using 3d printing?

More Narasimha Kalyan's questions See All

In order to learn HVAC design course, which is the best institute in south India or is it better to learn an online course?

I wish to do a diploma in HVAC design, is it better to do an online course if so suggest me from where should I get my diploma from?

04 May 2018 4,270 0 View

Can i use cad software in order to analyze the Water contacting angle(WCA)?

Currently, i am working on a project related to hydrophobic coatings. The problem we are facing is with the equipment availability. is it a good practice to use CAD to know WCA. below is the...

03 April 2018 8,556 4 View

Will material properties depend on specimen parameters?

In order to find the variation in compressive strength for a nanocoated specimen compared with original specimen. I recently performed a test, the results obtain are not in accordance with...

03 April 2018 795 6 View

How should we determine the post coating Temperature?

In case of nanocoatings, whatever the mixture is( a mixture of nanoparticles/ or a mixture of liquids),how can we determine the temperature to be set after we coat the specimen. Here I refer...

02 March 2018 5,521 2 View

Will properties of a nanocomposite-coating change ,when it has low m.p constituents in its composition & is subjected to high temperature?

Should I be afraid of change in compositional variation, if the nanocomposite coating I'm concentration on with low m.p material constituents is subjected to high temperature?

02 March 2018 6,619 3 View

What could be possible reasons for cadmium rich nanocomposite to be evaporating during stirring?

i am working on a project related to nanocomposite coatings, one of the compositions we are concentrating on is rich in cadmium content. The problem arised when we tried to stir the solution of...

02 March 2018 2,319 13 View

Which Material can be a substitute for mild steel?

Kindly suggest me a material that could replace mildsteel with corrosion resistance , currently I am working on mildsteel specimen surface grinding it is a time consuming process .

01 February 2018 4,973 5 View

What could be the easiest possible method to determine thermal conductivity of a nanocoatings specimen?

As a part of my project I wish to find thermal conductivity of nanocomposite coated specimen, what could be the easiest method to find it? Will an assumption related to concept of composite slab...

01 February 2018 9,428 4 View

How can I nano mask a material?

Inorder to impart surface roughness , I wish to remove material in nanosize. Instead of processes like plasma etching and wet chemical etching can I use a uv radiation box? If so , how can I nano...

31 December 2017 1,855 2 View

Which is the most convenient manufacturing software for Additive Manufacturing?

Which tools can be used to generate machine codes for additive manufacturing?

02 March 2021 7,220 2 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

I am looking for a simple software program to model 3D chemical bonds. The purpose is to generate high-quality graphical abstracts. Any suggestion?

Hello everyone: I am looking for a simple software program to model chemical bonds. The purpose is to generate a high-quality graphical abstract for a top leading journal in the field of...

23 February 2021 8,012 3 View

How can I measure the thickness of thin layers deposited on textured glass susbtrates?

I want to measure the thickness of aluminum oxide and titanium oxide layers deposited on textured glass substates. The layer thicknesses are typically below 100nm.

21 February 2021 5,465 4 View

Which programs are to be used to register 2D image onto a 3D image data set?

I am trying to register a light micrograph onto a 3D CT data set, as I want to extract the corresponding image from the CT data set. Is there any software or program can do this accurately? I am...

21 February 2021 8,220 3 View

What is the better software for approximation of 3D surface with equations?

I have a massive of x, y, z coordinates of 2D surface in 3D space, which builded in Ansys HFSS or AutoCAD. How can I get the analitical aproximation of this surface by formulas?

21 February 2021 3,444 7 View

How can I obtain Reaction Forces in ABAQUS?

I am trying to simulate a simplified version of a beam resting on 10 points using Abaqus. The solutions I want to obtain are the Reaction Forces in each resting point or area when applying a...

21 February 2021 3,075 2 View

How to convert 2D stack images to 3D to obtain surface area of nucleus?

I have 15 slices of the nucleus at different z-heights from confocal imaging. I would like to use these slices to reconstruct the 3D nucleus and ultimately estimate the surface area of the...

20 February 2021 6,967 1 View

How to get the vector of a specific vibration mode in phonon dispersion?

For example, I have this phonon dispersion(Fig. 1), and now I would like get vector of atoms which describes TA1 in P. I know v_sim can show vibrational animation of specific mode, but I do not...

20 February 2021 4,332 4 View

Has anyone used deep learning for 2D/3D REGISTRATION ?

I am a Master student in Biomedical (Bio-electrical) Engineering and work on " 2D-3D registration ( CT and X-Ray) as my thesis. I created DRR from CT and want use CNN( Convolutional Neural...

19 February 2021 6,354 3 View

Jaime Cuauhtemoc Negrete

Check plase this links maybe the articles helkp you with your question.Best Regards

https://s3.amazonaws.com/academia.edu.documents/36830426/Berman_3D-Printing.pdf?AWSAccessKeyId=AKIAIWOWYYGZ2Y53UL3A&Expires=1519043491&Signature=KFJu1ZyTpioj6tQilcx%2FnKcZI2U%3D&response-content-disposition=inline%3B%20filename%3DBerman_3D-Printing.pdf

http://pubs.rsc.org/-/content/articlelanding/2014/lc/c3lc50956g/unauth#!divAbstract

https://www.researchgate.net/profile/Frank_Piller/publication/276898572_Economic_Implications_of_3D_Printing_Market_Structure_Models_Revisited/links/562a41f608aef25a243ff3f6/Economic-Implications-of-3D-Printing-Market-Structure-Models-Revisited.pdf

https://www.researchgate.net/profile/Behzad_Esmaeilian/publication/301346190_The_evolution_and_future_of_manufacturing_A_review/links/5713ad9008aeff315ba35385/The-evolution-and-future-of-manufacturing-A-review.pdf

Recep Onler

Unfortunately, the current metal additive manufacturing systems do not have nanoscale resolution. Nanoscribe 2-photon lithography system and Optomec aerosol jet printing systems may provide submicron resolution with certain materials limitations.