Dynamic Time Historic Analysis in ABAQUS?

05 June 2015 2,433 1 View

Can anyone give me some information regarding static Riks analysis for concrete models in ABAQUS?

04 May 2015 1,032 2 View

Are you familiar with concrete damage plasticity modelling in Abaqus?

I'm modelling a steel beam to reinforced concrete column joint in Abaqus/standard. I use concrete damage plasticity model for concrete modelling, but I don't know what value should I input for...

03 April 2015 9,399 16 View

Does anyone know about this error massage in ABAQUS analysis "Too many attempts made for this increment"?

I'm doing nonlinear static analysis to investigate cyclic behavior of a connection. when i use Quadratic type in mesh module to my model it takes too longer time than Linear one, and when i use...

03 April 2015 3,005 7 View

Is it possible to estimate steel stress-strain curve without having the experimental data?

03 April 2015 8,397 2 View

Is it possible to see concrete cracking in Abaqus?

I would like to model a RC connection in Abaqus and analyze that under cyclic loading. My question is that, can I see how the connection starts to cracking and when? Thanks.

02 March 2015 9,039 5 View

Anyone familiar with the reinforcement of a concrete beam?

When the reinforcement is in to the concrete everything is ok. But I need some part of reinforcement to be out of concrete. At that time the outer part has not no displacement and no...

31 December 2014 6,560 13 View

What is the effect of decreasing PH on concrete properties?

10 November 2014 238 19 View

Is there any solution (like silica gel but liquid) that can protects another solution's activity (like bacteria culture) in environments with high PH?

10 November 2014 7,305 3 View

water absorption test

Does anyone know how can I access the RILEM 25 PEM(II-6)-water absorption test method? Or do you know another methods for doing this test?Please advise how can i get them? Thank you

09 October 2014 4,864 6 View

What is the procedure to determine the permeability of concrete?

can anyone help me in this, it will help me with my research work

01 March 2021 834 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Apart from Nanosilica and CNT's what are the other nanomaterials readily available to use in concrete mixture?

Nanotechnology in concrete materials

01 March 2021 3,379 3 View

How to remove fatty material from plant extract?

The resultant solid was partitioned three times with 250 ml of petroleum ether (40-60/c) to remove any fatty material and evaporated to dryness.

28 February 2021 9,464 2 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

Concrete compressive strength databases?

I am looking for datasets similar to this one: http://archive.ics.uci.edu/ml/datasets/Concrete+Compressive+Strength I am looking for concretes with different types of aggregates (Recycled,...

27 February 2021 6,801 3 View

LEDs on Vis Light photo degradation of MB water sol via N doped TiO2 in a mini flume?

Good day to all, I have no experience with light emitting diodes. I am building a glass mini flume to demonstrate the photo degradation of Methylene Blue in water running over self cleaning...

26 February 2021 4,026 5 View

What is the best way to calculate the angles of twist for concrete columns subjected to torsional moment using finite element software?

In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...

26 February 2021 3,806 2 View

Compute for the total volume of concrete needed for the concrete pouring of the foundation including its column up to NGL only as shown in the plan?

Looking for the quantity of cement, sand, and gravel of footings and columns. Thank you!

25 February 2021 3,092 2 View

What are the saturated salt solutions that can give specific relative humidity of 35%, 65% and 95% for conditioning wood specimens?

Due to the unavailability of climate rooms, I want to carry out an experiment that require the use of certain saturated salt solutions especially those that can condition the wood specimen to 35%,...

25 February 2021 8,139 1 View