How does the nano fiber diameter decrease while loading of MWCNT in ABS polymer solution during electrospinning ?

I have electrospun pure ABS solution and measured the diameter and it was measured as 500s nm averagely. But surprisingly the fiber diameter decreases to 100s nm averagely while loading of MWCNT....

08 September 2018 2,628 1 View

Unknown RI and Absorption Coeff of the material in DLS for size distribution ?

We have Malvern DLS Zetasizer instrument in our lab. I need to determine the size analysis by DLS method. I need to input the properties like RI and absorption Coeff of the material. Is there any...

09 October 2017 2,596 0 View

What are the major following steps to follow for purification of waste cooking oil for transesterification ?

I have collected some waste cooking oil from hotels and it contains lots of left over fried items and loaded with carbon (black soot). I have to use it for my research work but finding hard in...

08 September 2017 6,210 0 View

How does a layer structure material enhances in catalytic properties of the material ?

After a novel synthesis method of a compound, I have found it as layered structure when I observed in SEM. This material was not having the layer structure before synthesizing it with the novel...

07 August 2017 5,058 5 View

What makes the base catalyst reacts faster than acid catalyst during trans-estrification ?

Normally, the base catalyst complete its reactions within 1 hour where as the acid catalyst tends to finish within 2 hours during transesterification. What mechanism makes the base catalysts react...

05 June 2017 1,028 0 View

Which method is good for doping among this two methods ? 1. wet impregnation and 2. Hydrothermal or solvothermal process.

I'm trying to impregnate the nanoparticles in micron size powder. Firstly I was trying with wet impregnation method. I guess the proper doping is not happening. Will hydrothermal or solvothermal...

05 June 2017 3,766 0 View

Why does the magnetic property is losing while keeping the sample (Fe3O4) for calcination 500-900 degree Celcius?

i have synthesised magnetic material Fe3O4 by co-ppt method. Before calcination, the magnetic property was showing but after calcination above 500 degree C , the magnetic property is losing....

01 February 2017 5,302 6 View

What is the best method to coat Cerium Zirconium oxide on copper tube ?

I'm trying to coat the Cerium Zirconium oxide NPs on copper tube. I have tried brush coating and dipped coating but its not sticking on the copper tube. Any suggestion for better coating, Please...

31 December 2016 9,019 1 View

Can i get the top rated journals list with high impact factor from nano catalyst for the biodiesel transestrification process ?

31 December 2016 6,339 1 View

Did anyone has reported the eggshell SEM image in flower like structure ?

if anyone here read the paper about eggshell and reported the SEM image as flower-like structure then please let me know the name of the paper.

31 December 2016 7,772 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Physics: Why do we describe light by referring to its wavelength, but microwaves and radar pulses by referring to their frequency?

In physics, the description of the properties of light generally refers to its wavelength (nm), while in the range of microwaves and radio waves we refer to the frequency of a signal (e.g. kHz or...

03 March 2021 1,682 3 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

Is there any effect of different colours of light (white, red, yellow, blue etc.) on the rate of photosynthesis? If yes, why?

Light is inevitable for the process of photosynthesis reaction. Naturally sunlight plays the vital role for this process. Light may be of different colours like white, red, yellow, blue etc....

02 March 2021 7,890 2 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View